Оборудование для дозирования и формования композитов
122 просмотра

Пресс для композитов | PCM и SMC

Многоцилиндровый гидравлический пресс с активной системой выравнивания плит для заданной оснастки для композитов и цельных преформ.

Nominal Pressing Force

Nominal Pressing Force: 30,000 kN (approximately 3,059 metric tonnes-force); configuration-specific reference

Hydraulic Working Pressure

25.0 to 31.5 MPa (Main hydraulic cylinder system)

Platen Leveling Reference

±0.02 mm (4-Corner active dynamic leveling precision); configuration-specific reference

Fast Platen Descent

Up to 400 mm/s (Servo gravity fast approach); Platen descent stroke; configuration-specific reference

Наличие по запросу Срок поставки — по предложению Гарантия 1 год
3,000-Ton High-Tonnage SMC/PCM Chassis Part Molding

Precision Active-Leveling Compression for Structural Leaf Springs

Многоцилиндровый гидравлический пресс с активной системой выравнивания плит для заданной оснастки для композитов и цельных преформ.

Многоцилиндровый гидравлический пресс с активной системой выравнивания плит для заданной оснастки для композитов и цельных преформ.

Press frame, hydraulic power/accumulator, platen-leveling feedback, heating and controls. Prepreg/SMC charge, molds, handling and part qualification are separately agreed.

Nominal pressing force is 30,000 kN, approximately 3,059 metric tonnes-force. Hydraulic-system pressure, tool cavity pressure and platen leveling are separate quantities. Spring weight and fatigue figures describe the specified finished-part comparison and test.

Концептуальная иллюстрация: Сгенерированная концептуальная иллюстрация для обсуждения процесса; это не фотография указанной машины, предприятия заказчика или реализованного проекта.

Precision Active-Leveling Compression for Structural Leaf Springs

Поток материалов и принцип работы

Automated Charge Stacking & Preheating

High-strength continuous glass fiber epoxy prepreg sheets (PCM) or high-fiber vinyl SMC blanks are cut by ultrasonic knives and robotically stacked into a parabolic charge pack.

Fast Robot Placement in Heated Tooling

A specialized pneumatic needle gripper transfers the thick charge pack into the lower tool cavity heated to 150°C ± 1°C inside the 3,000-ton press.

High-Speed Closing & Active Micro-Leveling

The press descends at 400 mm/s; upon contact, four corner leveling cylinders engage, ramping to full 3,000-ton force in 1.8 seconds while holding parallelism within ±0.02 mm.

Isothermal High-Pressure Consolidation

The tool maintains continuous 12.0 MPa cavity pressure for 180 seconds, ensuring dense resin flow into parabolic tapers and crosslinking the matrix without internal voids.

Automated Extraction & Deflashing

Platen cylinders de-pressurize and open smoothly; hydraulic bottom ejector pins elevate the hot leaf spring for robotic extraction and robotic edge-milling.

Нужно коммерческое предложение на это оборудование?

Запросить предложение
Данные конфигурации

Модель и технические параметры

Supplied HF-PCM3000-AL configuration references for the selected material, tooling and operating conditions. Nominal pressing force is 30,000 kN, approximately 3,059 metric tonnes-force. Hydraulic-system pressure, tool cavity pressure and platen leveling are separate quantities. Spring weight and fatigue figures describe the specified finished-part comparison and test.

Технический параметрHF-PCM3000-AL
КомпонентыSolid preform or prepreg tooling; no liquid proportioning
Электропитание380 В, 3 фазы, 50 Гц (по заказу 440 В/480 В 60 Гц)
Рабочее давление25.0 to 31.5 MPa (Main hydraulic cylinder system)
Масса145,000 kg (Complete press frame, cylinders, and hydraulics)
Габариты (Д×Ш×В)6200 mm x 4500 mm x 7800 mm (Machine bed footprint & height)
Active Leveling Precision≤ 0.02 mm (Under 30,000 kN off-center load); Optical linear encoders on 4 corners; configuration-specific reference
Full Pressurization Time≤ 1.8 seconds (Ramp to 3,000-ton clamp); High-speed accumulator assist; configuration-specific reference
Platen Fast Downward SpeedUp to 400 mm/s (Servo gravity fast approach); Platen descent stroke; configuration-specific reference
Leaf Spring Fatigue Durability≥ 1,000,000 Cycles (Full load bench test); Automotive leaf spring test rig; configuration-specific reference
Nominal pressing forceNominal Pressing Force: 30,000 kN (approximately 3,059 metric tonnes-force); configuration-specific reference
Supplied preform fiber fraction60% to 70% Fiber Content by weight (Prepreg formulation); configuration-specific reference
Active platen leveling precision±0.02 mm (4-Corner active dynamic leveling precision); configuration-specific reference
Hydraulic oil reservoirHydraulic oil reservoir: 4,500 L (Mineral hydraulic fluid); configuration-specific reference
Комплектация оборудования

Ключевые особенности оборудования

Press frame, hydraulic power/accumulator, platen-leveling feedback, heating and controls. Prepreg/SMC charge, molds, handling and part qualification are separately agreed.

±0.02 mm 4-Corner Active Leveling

Supplied configuration reference: Four independent digital servo cylinders correct platen tilt dynamically under severe off-center parabolic spring charges. Actual capability requires material and tooling validation.

Configured Pressurization Sequence

Coordinate the hydraulic pressure ramp, tool closure and consolidation with the selected prepreg or SMC reaction window. The nominal force is 30,000 kN; complete cycle time includes handling and cure.

Composite Part and Tooling Interfaces

Select charge, molds, thermal cycle and handling for the intended spring or panel. Component weight and fatigue requirements are evaluated on the finished design.

1 Million Fatigue Cycle Lifespan

The supplied 1,000,000-cycle reference is a finished-spring bench result for the specified material, geometry and loading; it is not a press rating or general fatigue-life guarantee.

Обсудите конфигурацию вашего оборудования

Сообщите о вашей продукции, материалах, оснастке и требованиях к производству, чтобы мы могли рассмотреть оборудование и интерфейсы для вашего проекта.

Вопросы планирования

Часто задаваемые вопросы

Why is ±0.02 mm active leveling critical when molding parabolic leaf springs?
Asymmetric charges exert uneven tipping forces; precise leveling ensures uniform thickness to prevent delamination. Confirm the applicable material, tooling, test method and original records for the specified configuration.
How does 1.8-second fast pressurization benefit fast-curing epoxy prepregs?
Fast pressure ramping consolidates prepreg plies before heat triggers gelation, preventing uncompressed voids. Confirm the applicable material, tooling, test method and original records for the specified configuration.
What enables composite leaf springs to survive 1 million fatigue cycles?
The supplied million-cycle reference concerns a finished spring under its stated load and test procedure. Consolidation and platen leveling support process control; internal voids and fatigue life require separate part inspection and testing.
Can this press also mold carbon fiber battery covers and chassis panels?
Yes, high tonnage (3,000 tons) and active leveling support large-area SMC/PCM panels up to 3.5 m². Confirm the applicable material, tooling, test method and original records for the specified configuration.

Готовы обсудить ваш проект?

Свяжитесь с нашей командой
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube