
حل قولبة رغوة البولي يوريثان ذات القشرة المتكاملة
Configure integral-skin PU armrests and furniture components with defined surface and cleaning tests.
Precision Polyurethane Integral Skin Solutions for Ergonomic & Medical Furniture
Integral-skin furniture parts combine a molded outer skin and cellular core around the selected geometry and inserts. Skin formation, touch and surface integrity depend on the formulation, tool and cure. Use in healthcare furniture does not by itself establish resistance to every disinfectant or a medical qualification.
نطاق توريد محدد
Define the metering, fixtures, mold handling and any coating stage. Verify water-blown compatibility, skin quality and insert bonding with the selected material system.
المدخلات لاختيار العملية
Part and insert drawings, desired touch, surface finish, cleaning regime, abrasion method, shot mass and output.
Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Define the metering, fixtures, mold handling and any coating stage. Verify water-blown compatibility, skin quality and insert bonding with the selected material system.
Integral Skin PU Foam Molding Workflow
Prepare inserts and tooling → Condition and dispense → Mold and cure → Inspect and clean-test. Define preparation, filling, cure and output timing separately for the selected configuration.
Prepare inserts and tooling
Confirm insert location, mold finish and the required surface system.
التكييف والتوزيع
Establish material conditions and the filling sequence for the part.
Mold and cure
Validate skin/core formation, venting and the thermal sequence.
المواصفات الفنية
مراجع التكوين الحالي والاختبار. تُعد إعدادات المعدات ونتائج المواد ونتائج التجميع النهائي منفصلة؛ ويُطبَّق كل قيمة فقط على التكوين والظروف الموثقة الخاصة بها.
| المعلمة الفنية | المواصفة القياسية / القيمة | السياق الهندسي & التحقق |
|---|---|---|
| التطبيق المستهدف | Medical Furniture Armrests, Office Chair 3D/4D Pads | Tactile high-wear furniture interfaces |
| مصفوفة المواد | Polyurethane Integral Skin Elastomer (Water-Blown) | Eco-friendly zero-ODP formulation |
| Surface Hardness Range | Shore A 45 to Shore A 80 (Customizable) | Tailored from plush softness to rigid grips |
| نطاق كثافة اللب | 250 – 450 kg/m³ | High shock-absorbing microcellular core |
| قدرة إخراج قياس الجرعات | 10 – 35 kg/min (Customizable) | Micro-shot precision servo axial pumps |
| زمن دورة نزع القالب | 90 – 140 seconds (Standard 120 s) | High-cadence multi-carrier production |
| Taber Abrasion Test | Acceptance target agreed for the selected specimen | State the method, abrasive wheel, load, conditioning, cycle count and endpoint in the report |
| Wyzenbeek Abrasion Test | Separate result where the method is applicable | State the method, abradant, tension/load, conditioning, double-rub count and failure criterion; do not convert it to a Taber rating |
المعدات الخاصة بهذا الحل
تُختار مراجع المعدات وفق عمليتها الموثّقة. القياس الرئيسي للجرعات والإمداد المساعد والمسارات البديلة ليست حزمة قياسية واحدة.
ضوابط العملية وفحوص التطبيق
قيّم هذه الوظائف باستخدام المادة والتجهيزات القالبية الموجزة الإنتاجية المختارة. تتطلب نتائج الأجزاء النهائية أدلة قبول خاصة بها.
Defined skin inspection
Agree the permitted pores, pinholes and texture variation instead of assuming a flawless surface.
Cleaning-specific validation
Test the actual disinfectant, concentration, exposure and repeated cleaning cycles.
Component-specific feel
Establish hardness and support response on the selected material and molded geometry.
مشاريع ذات صلة
هذه مراجع تطبيقية ذات صلة. قارن المادة الفعلية والعملية والوحدات المسلّمة؛ فأرقام المشاريع المبلَّغ عنها ليست نتائج قبول لخط آخر.

مشروع خط إنتاج البولي يوريثان المتكامل الجلد للأثاث الطبي في روسيا

مشروع خط إنتاج البولي يوريثان المتكامل الجلد لمساند ذراعي كرسي المكتب في الصين
الأسئلة الشائعة
إجابات حول اختيار العملية وتكامل المعدات ودعم التسليم.
Does an integral skin repel every hospital disinfectant?
Does mold tilting eliminate pinholes?
ما المعلومات المطلوبة لإعداد تكوين أولي؟
ناقش مشروع إنتاج الأثاث الخاص بك
Share the following with your production brief: Part and insert drawings, desired touch, surface finish, cleaning regime, abrasion method, shot mass and output. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.