Стандартная операционная процедура (СОП) отрезки заготовок ленточной пилой: спецификации точности процесса — фон баннера

Стандартная операционная процедура (СОП) заготовительной резки ленточной пилой: технические требования к точности процесса

Настоящая СОП устанавливает требования к точности заготовительной резки ленточной пилой, проверкам станка и пильного полотна, закреплению заготовки, параметрам резки, контролю, удалению заусенцев и устранению неисправностей для компонентов полиуретанового оборудования Haifeng.

Концепция отрезки заготовок ленточной пилой из металлической трубы: зажатая заготовка, отрезанные заготовки, угольник и штангенциркуль

Точность подгонки под сварку полиуретанового оборудования Haifeng закладывается уже на этапе резки заготовок на ленточной пиле. Каждое отклонение перпендикулярности поверхности реза на 0,5°/100 мм может увеличить неравномерность зазора при подгонке под сварку более чем на 0,3 мм и повысить сварочные деформации на 20%–30%, что в итоге выводит плоскостность монтажного основания серводвигательного дозирующего насоса за допуск при финальной сборке. Если перпендикулярность торцов заготовок опор трубопроводов или фланцев превышает 0,2 мм/100 мм, уплотнительные поверхности фланцев после сварки могут перекоситься и снизить долю успешных испытаний резервуара на герметичность (требование Haifeng: отсутствие утечек при 0,02 МПа в течение 30 мин).

Ключевые технологические параметры — краткий обзор:

ПараметрСтандарт HaifengОтраслевой ориентирСвязанный показатель точности
Допуск на длину заготовки (L <3000 мм)±1,0 мм±1,0 ммЗазор при подгонке под сварку ≤0,5 мм
Допуск на длину заготовки (L ≥3000 мм)±0,5 мм±0,5 ммОдинаковая длина труб рамы
Перпендикулярность поверхности реза (высота ≤200 мм)≤0,2 мм/100 мм≤0,5°Контакт при подгонке под сварку
Перпендикулярность поверхности реза (высота >200 мм)≤0,15 мм/100 мм≤0,3°Совмещение шва обечайки после вальцовки
Шероховатость пропиленной поверхностиRa ≤12,5 мкмRa ≤12,5 мкмПоверхность под сварку без масляных загрязнений
Высота заусенца на торце реза≤0,1 мм на поверхности под сварку≤0,5 ммКонтроль пористости шва/непровара
Радиальное биение пильного колеса≤0,15 мм0,12–0,20 ммПрямолинейность пропиленной поверхности ≤0,3 мм/м
Торцевое биение пильного колеса≤0,15 мм0,12–0,20 ммПлоскостность пропиленной поверхности
Точность хода направляющих полотна по горизонтали≤0,10 мм/100 мм≤0,15 мм/100 ммПерпендикулярность реза ≤0,2 мм/100 мм
Точность позиционирования подающей системы≤±0,10 мм/500 мм≤±0,20 мм/500 ммКоэффициент вариации длины в партии CV ≤0,3%
Повторяемость позиционирования системы подачи≤±0,05 мм≤±0,10 ммСтабильные размеры заготовок в партии
Натяжение полотна (сталь)20–25 Н/мм²15–30 Н/мм²Отклонение полотна ≤0,1 мм/м
Скорость резания (углеродистая сталь Q235B/Q345B)60–100 м/мин50–120 м/минБаланс качества реза и производительности
Скорость резания (нержавеющая сталь 304/316L)30–50 м/мин30–60 м/минКонтроль наклёпа и стойкости инструмента
Скорость резания (алюминий 6061/7075)200–400 м/мин200–500 m/minControl burrs
Feed per tooth (carbon steel)0.04–0.08 mm/tooth0.04–0.16 mm/toothBalance chip shape and cutting force
Coolant concentration8%–12% emulsion5%–15%Blade life ≥3000 cuts
Blanking ambient temperature10–40°C—Thermal expansion effect ≤0.01 mm/m

1. Область применения

1.1 Применимые операции

This SOP applies to bandsaw blanking of the following Haifeng polyurethane-equipment components:

Part to cutТипичный материалTypical sizeПоказатель соответствующего оборудования
Frame square tube/rectangular tubeQ235B/Q345B40×40–120×120 mmFrame weld-fit-up gap ≤0.5 mm
Tank-shell plate blank304/316L3–8 mm thickTank-shell seam accuracy after rolling
Pipeline-support sectionsQ235B/304Angle/channel/flat barAccurate pipeline fixing-point position
Round-bar flange blanks304/316L/45#Φ50–Φ300 mmFlange sealing-face flatness ≤0.02 mm
Pouring-platform frame sectionsQ235B/Q345BSquare/rectangular tubePouring-path repeatability ±0.05 mm
Electrical-cabinet bracketsQ235B/cold-rolled sheetAngle/flat barAlignment of cabinet mounting holes
Mixing-head mounting-base blanksAlloy steel/45#Φ80–Φ200 mmMixing-head alignment ≤0.03 mm

2. Подготовка к работе и проверка точности станка

2.1 Проверка технической документации и материала

№ПунктТребование к точностиКритерий приёмки
1Blanking listMaterial, size, quantity, and cut length specifiedMatches BOM
2Сертификат на материалМарка соответствует чертежуChemical-composition and mechanical-property reports included
3Visual material inspectionNo bending, twisting, or rustBend ≤2 mm/m; twist ≤1°/m
4Actual material dimensionsSection-size deviation ≤±0.5 mmMeasure with vernier caliper and record
5Blanking process cardSaw parameters, clamping plan, and inspection requirementsIncludes weld-shrinkage allowance

2.2 Проверка точности станка

Calibrate the bandsaw regularly under the machine calibration procedure; calibration error for critical parameters must be ≤0.05 mm. Perform accuracy inspection according to JB/T 15187.1-2025, “CNC Horizontal Bandsawing Machines—Part 1: Accuracy Inspection,” and JB/T 4318.1-2026, “Horizontal Bandsawing Machines—Part 1: Accuracy Inspection.”

Параметр калибровкиСтандарт HaifengПериодичностьСредство контроля
Radial runout of drive/idler saw wheels≤0,15 ммЕжеквартальноDial indicator and magnetic base
Face runout of drive/idler saw wheels≤0,15 ммЕжеквартальноИндикатор часового типа
Плоскостность рабочего стола≤0.10 mm/500 mmЕжеквартальноPrecision level/straightedge and feeler gauge
Точность хода направляющих полотна по горизонтали≤0,10 мм/100 ммЕжемесячноDial indicator and master test piece
Blade-position error from combined guide errors≤0,15 ммЕжемесячноIndicator
Точность позиционирования подающей системы≤±0,10 мм/500 ммЕжемесячноLaser distance meter/master gauge block
Повторяемость позиционирования системы подачи≤±0,05 ммЕжемесячноDial indicator and master test piece
Saw-frame travel parallelism to guideway≤0.10 mm/1000 mmКаждые 6 месяцевDial indicator and straightedge
Blade perpendicularity to worktable≤0.1 mm/100 mmЕжемесячноSquare and feeler gauge

2.3 Проверка точности полотна и оснастки

Tool/componentТребование к точностиПериодичностьСредство контроля
Blade tooth pitchMatch workpiece section sizeEach blade batchTooth-pitch gauge
Blade tooth setSymmetric left/right; deviation ≤0.05 mmEach blade batchCaliper
Blade wearTooth-tip wear ≤0.10 mmКаждую сменуMagnifier/touch
Blade tension20–25 N/mm² (steel)Каждую сменуTension tester
Guide-block clearance0.05–0.10 mmWeeklyFeeler gauge
Guide-wheel wear≤0.10 mmЕжемесячноИндикатор часового типа
Feed-vise jaw parallelism≤0.05 mm/100 mmЕжемесячноИндикатор часового типа

3. Структурированный рабочий процесс отрезки заготовок ленточной пилой

3.1 Подготовка перед сменой и прогрев

3.1.1 Проверка состояния станка

Switch on the main power, then start the saw and CNC system. After the self-check completes without alarms, home the saw frame. Check the following:

1. Blade tension meets the set value (20–25 N/mm² for steel; reduce as appropriate for aluminum).

2. Coolant level and concentration are correct (8%–12% for stainless; 5%–8% for carbon steel).

3. Hydraulic pressure is stable within machine requirements (typically 4–6 MPa).

4. Feed-vise and clamping-vise jaws are clean and within wear limits.

3.1.2 Bandsaw no-load warm-up

Warm up the saw unloaded before precision blanking (such as flange blanks and mixing-head mounting-base blanks):

Blanking typeWarm-up timeСпособ
General accuracy (length tolerance ±1.0 mm)≥5 minRun blade unloaded and cycle saw frame up/down
Precision (length tolerance ±0.5 mm)≥10 минRun blade at cutting speed and traverse feed system full stroke
High accuracy (length tolerance ±0.3 mm)≥15 minSimulate cutting conditions and monitor hydraulic-oil temperature

3.2 Зажим заготовки и установление баз

3.2.1 Control clamping accuracy

Secure clamping directly determines blank length and end-face perpendicularity. Before clamping, clean vise jaws and workpiece locating faces and remove burrs and oil.

Clamping methodSuitable workpieceLocating accuracyNotes
Hydraulic vise (standard jaws)Square/round bar, rectangular tube≤0.10 mmJaws must be perpendicular to blade
Dedicated V-jawsRound bar, pipe≤0,05 ммV face must be perpendicular to blade
Multi-part fixtureSmall sections in batch≤0.10 mmUse spacers to locate each piece
Dedicated locating fixtureFlange blanks, mixing-head mounting bases≤0,05 ммCheck locating-pin wear regularly

3.2.2 Set and locate blank length

Locating methodAccuracyПрименение
Manual stop±0,5 ммSingle pieces/small batches
Digital scale±0.1 mmBatch blanking
Servo feed system±0.05 mmHigh-accuracy batch work (flange blanks)
Laser positioning±0.03 mmPrecision blanks (mixing-head mounting base)

3.3 Параметры резки и контроль точности

3.3.1 Material groups and sawing parameters

Materials cut for Haifeng equipment mainly include carbon steel (Q235B/Q345B), stainless steel (304/316L), aluminum alloy (6061/7075), and alloy steel (45#/40Cr).

Recommended parameters for Q235B/Q345B carbon steel:

Workpiece section (mm)Cutting speed Vc (m/min)Feed per tooth (mm/tooth)Blade pitch (mm)Blade tension (N/mm²)
≤5080–1000.06–0.084–620–25
50–10070–900.05–0.076–820–25
100–20060–800.04–0.068–1022–25
>20050–700.04–0.0510–1222–25

Recommended parameters for 304/316L stainless steel:

Workpiece section (mm)Cutting speed Vc (m/min)Feed per tooth (mm/tooth)Blade pitch (mm)Blade tension (N/mm²)
≤5040–500.04–0.064–622–25
50–10035–450.03–0.056–822–25
100–20030–400.03–0.048–1025–28
>20030–350.02–0.0310–1225–28

Austenitic stainless steel (304/316L) work-hardens strongly, so its cutting speed must be substantially lower than for carbon steel. Because molybdenum makes 316L more prone to work hardening than 304, reduce speed further and increase tension as appropriate to prevent blade deflection. Chip shape and color indicate whether speed and feed are suitable: white, curled chips are generally desirable; short, hard blue chips indicate low speed and high feed; thin, loose or powdery white chips indicate excessive speed.

Recommended parameters for 6061/7075 aluminum alloy:

Workpiece section (mm)Cutting speed Vc (m/min)Feed per tooth (mm/tooth)Blade pitch (mm)Blade tension (N/mm²)
≤50300–4000.08–0.123–515–20
50–100250–3500.06–0.105–715–20
100–200200–3000.05–0.087–918–22

3.3.2 Inspect sawing accuracy

Inspection itemСтандарт HaifengСредство контроляПериодичность
Blank length deviation (L <3000 mm)±1,0 ммTape measure/caliper100% inspection
Blank length deviation (L ≥3000 mm)±0,5 ммTape measure100% inspection
End-face perpendicularity (height ≤200 mm)≤0,2 мм/100 ммSquare and feeler gaugeFirst article and sampling
End-face perpendicularity (height >200 mm)≤0,15 мм/100 ммSquare and feeler gaugeFirst article and sampling
Sawn-face straightness≤0.3 mm/mStraightedge and feeler gaugeFirst article each batch
Surface roughnessRa ≤12,5 мкмRoughness tester/comparator couponSampling
Burr height on weld-fit-up face≤0.1 mmMagnifier/touch100% inspection

3.4 Удаление заусенцев и обработка торцов

3.4.1 Deburring requirements

Burrs on sheet-metal mating faces and weld-fit-up faces must be ≤0.1 mm. After deburring, use a chamfering tool or belt sander to create a 0.1–0.3 mm × 45° chamfer.

3.4.2 Maintain accuracy after end-face finishing

Recheck end-face perpendicularity after deburring to confirm that finishing did not introduce deviation. For precision blanks (flange blanks and mixing-head mounting-base blanks), recheck perpendicularity with a CMM or precision square.

4. Ключевые параметры точности отрезки заготовок ленточной пилой

№CategoryПараметрСтандарт HaifengСредство контроляПериодичность
1Machine accuracyРадиальное биение пильного колеса≤0,15 ммИндикатор часового типаЕжеквартально
2Machine accuracyТорцевое биение пильного колеса≤0,15 ммИндикатор часового типаЕжеквартально
3Machine accuracyПлоскостность рабочего стола≤0.10 mm/500 mmPrecision levelЕжеквартально
4Machine accuracyТочность хода направляющих полотна по горизонтали≤0,10 мм/100 ммDial indicator/master test pieceЕжемесячно
5Machine accuracyFeed positioning accuracy≤±0,10 мм/500 ммLaser distance meterЕжемесячно
6Machine accuracyFeed repeat positioning≤±0,05 ммDial indicator/master test pieceЕжемесячно
7Cutting parameterНатяжение полотна (сталь)20–25 Н/мм²Tension testerКаждую смену
8Cutting parameterCarbon-steel cutting speed60–100 м/минTachometerКаждую смену
9Cutting parameterСкорость резания 316L30–50 м/минTachometerКаждую смену
10Blank accuracyLength deviation (L <3000 mm)±1,0 ммTape measure/caliper100% inspection
11Blank accuracyLength deviation (L ≥3000 mm)±0,5 ммTape measure100% inspection
12Blank accuracyEnd-face perpendicularity (height ≤200 mm)≤0,2 мм/100 ммSquare/feeler gaugeFirst article + sampling
13Blank accuracyEnd-face perpendicularity (height >200 mm)≤0,15 мм/100 ммSquare/feeler gaugeFirst article + sampling
14Blank accuracySawn-face straightness≤0.3 mm/mStraightedge/feeler gaugeFirst article
15Surface qualitySurface roughnessRa ≤12,5 мкмRoughness tester/couponSampling
16Surface qualityBurr height on weld-fit-up face≤0.1 mmMagnifier100% inspection
17Process allowanceTransverse weld-shrinkage allowance0.5 mm per seamReview blanking list100% inspection
18Process allowanceLongitudinal weld-shrinkage allowance2–3 mm/mReview blanking list100% inspection
19EnvironmentBlanking temperature10–40°CTemperature/humidity loggerContinuous

5. Типичные проблемы и технологические ошибки

5.1 Отклонение полотна вызывает чрезмерную погрешность перпендикулярности торца

Symptom: Cut-face perpendicularity to the workpiece axis exceeds 0.2 mm/100 mm; weld-fit-up gaps are uneven and the frame bends after welding.

Root cause: Blade deflection is the main cause of excessive end-face perpendicularity error. Causes include insufficient blade tension (below 80% of set value), excessive guide-block clearance (above 0.10 mm), worn guide wheels or bearing movement, excessive feed, and a blade tooth pitch that does not suit the section. The guide-angle assembly may also hold the blade out of perpendicular to the worktable.

Corrective actions:

1. Measure blade tension every shift; keep it at 20–25 N/mm².

2. Check guide-block clearance weekly; replace blocks if clearance is outside 0.05–0.10 mm.

3. Check guide-wheel wear monthly; replace wheels if wear exceeds 0.10 mm.

4. After blade installation, adjust guide-angle bolts until the blade is square to the table; verify with a square.

5. Select blade pitch to match the workpiece section (approximately 1/10–1/15 of section size).

5.2 Разрыв полотна прерывает резку и создаёт риск для безопасности

Symptom: The blade suddenly breaks during cutting, leaves a mark on the workpiece, and requires reclamping and recutting.

Root cause: Causes include excessive tension (above 120% of set value), excessive cutting speed and overheating, excessive feed that overloads teeth, incorrect tooth pitch, or inadequate coolant/lubrication that causes chips to adhere to teeth. Frequent blade breakage, angled cut faces, excessive burrs, and rapid blade wear are common shop-floor problems.

Corrective actions:

1. Follow the blade-tension standard strictly (20–25 N/mm² for steel); keep deviation within ±5% of the set value.

2. Select cutting speed by material (carbon steel 60–100 m/min; 316L 30–50 m/min).

3. Adjust feed in real time based on chip shape; white curled chips indicate a desirable condition.

4. Keep coolant concentration and flow within limits, and direct coolant accurately at the kerf.

5. Before use, inspect tooth-tip wear (≤0.10 mm) and tooth-set symmetry.

5.3 Накопленное отклонение длины заготовки затрудняет подгонку под сварку

Symptom: Length variation in batch-cut square stock increases, lengths do not match during fit-up, and extensive rework is needed.

Root cause: Feed positioning accuracy or repeatability has deteriorated. Worn feed-vise jaws, a worn feed screw, or encoder-signal interference can cause positioning error. Changing friction between the workpiece and support rack can also make actual feed length differ from the set value.

Corrective actions:

1. Check feed positioning monthly with a laser distance meter; maintain ≤±0.10 mm/500 mm.

2. Check repeat positioning monthly; maintain ≤±0.05 mm.

3. Replace feed-vise jaws if wear exceeds 0.05 mm.

4. Remove chips and debris from support racks before feeding to keep resistance stable.

5. For batch work, sample-check length every 20 pieces and recalibrate immediately if a drift trend appears.

5.4 Наклёп при резке заготовок из нержавеющей стали вызывает аномальный износ полотна

Symptom: Blade life when cutting 316L drops sharply (below 500 cuts), cutting force rises, and a hardened layer and burrs appear on the cut face.

Root cause: Austenitic stainless steel (304/316L) work-hardens strongly; surface hardness during sawing can increase from HB 150 to above HB 300. Excessive speed or insufficient feed makes blade teeth repeatedly cut the hardened layer and accelerates wear. Molybdenum makes 316L more prone to work hardening than 304.

Corrective actions:

1. Keep 316L cutting speed at 30–50 m/min; do not use carbon-steel speeds.

2. Use a “high-feed, low-speed” strategy so teeth always cut below the hardened layer.

3. Increase blade tension as appropriate (25–28 N/mm²) to resist deflection.

4. Use an M42 bi-metal blade or carbide-tipped blade for better wear resistance.

5. Ensure coolant fully covers the kerf to prevent heat buildup from worsening work hardening.

5.5 Неправильная концентрация СОЖ вызывает налипание стружки и шероховатость поверхностей реза

Symptom: Chips adhere to the cut face, burrs increase, roughness exceeds Ra 12.5 μm, and chip spaces between teeth become blocked.

Root cause: Coolant concentration is outside the recommended range. Stainless-steel machining requires adequate lubrication and cooling. Emulsion below 8% provides insufficient lubrication and encourages chip adhesion; above 15%, cooling declines, foam increases, and chip evacuation worsens. Incorrect concentration is a common cause of chip adhesion and rough sawn faces.

Corrective actions:

1. Use 8%–12% emulsion for stainless steel and 5%–8% for carbon steel.

2. Measure and record coolant concentration with a refractometer every shift.

3. Regularly remove chips and floating oil from the coolant tank to prevent bacterial growth.

4. Aim coolant nozzles at the kerf for effective cooling and chip flushing.

5.6 Износ направляющих блоков постепенно ухудшает перпендикулярность реза

Symptom: After the saw has been used for a period, end-face perpendicularity gradually moves out of tolerance and the cut becomes angled.

Root cause: Guide blocks maintain blade-position accuracy. Wear increases clearance between the blocks and blade, allowing cutting forces to push the blade sideways and tilt the cut face. Guide-block wear is one of the most common causes of bandsaw accuracy loss. Radial movement in saw-wheel bearings and worn guide-wheel grooves can also affect perpendicularity.

Corrective actions:

1. Check guide-block clearance weekly; replace blocks if it is outside 0.05–0.10 mm.

2. Use wear-resistant alloy guide blocks; do not substitute ordinary carbon steel.

3. Check saw-wheel bearing movement monthly; replace bearings if movement exceeds 0.05 mm.

4. Check guide-wheel grooves monthly; replace a wheel if a pronounced groove has formed.

5. Keep a guide-block replacement log with service intervals and sawing-accuracy measurements.

Системы подачи IBC: проверки переналадки и разделения материалов
Блог

Системы подачи IBC: проверки переналадки и разделения материалов

Надёжность системы подачи из IBC-контейнеров определяется её последовательностью переключения. Две промежуточные ёмкости (IBC) с одинаковым номинальным полиолом могут поступить с разными…

17 нояб. 2026 г.
Когда производство PU-колёс оправдывает автоматическую линию?
Блог

Когда производство PU-колёс оправдывает автоматическую линию?

Производство PU-колёс оправдывает автоматическую линию, когда узкое место сместилось с самой заливочной станции. Это происходит, когда целевые объёмы выпуска больше не…

16 ноября 2026 г.
Прессование SMC и спрей-трансферная заливка для корпусов аккумуляторов электромобилей
Блог

Прессование SMC и спрей-трансферная заливка для корпусов аккумуляторов электромобилей

При выборе между прессованием SMC и напылением с переносом для композитных крышек аккумуляторных батарей обычно решающим становится вопрос цены оснастки — и это не тот вопрос, с которого стоит начинать.…

15 ноября 2026 г.

Обсудите ваши требования к производству полиуретана

Расскажите о вашем применении, системе материалов, целевом объёме выпуска и требованиях к автоматизации. Инженерная команда Haifeng поможет вам рассмотреть варианты оборудования и производственных линий. Наша команда ответит в течение одного рабочего дня. Как только требования будут ясны, мы предоставим предварительное предложение в течение двух рабочих дней.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube