Metal-Core MC Nylon Gear Casting Solution Banner background

Решение для литья шестерен из MC-нейлона с металлическим сердечником

Coordinate metal-hub preparation and vacuum-assisted MC Nylon casting for a defined hybrid gear design.

Конфигурация процесса

Heavy Torque Capacity Meets Acoustic Silence in Industrial Drives

Hybrid gear casting combines a prepared metal hub, mechanical interlock, heated tooling and the selected nylon reaction system. Hub preheating and vacuum assistance support processing but do not prove zero residual stress, no voids or a universal torque capacity. Gear noise is an assembled-drive measurement.

Определенный объем поставки

Specify hub preparation, induction heating, casting, thermal treatment and machining. Gear tooth design and drivetrain qualification remain separate from the material-delivery package.

Исходные данные для выбора процесса

Hub/tooth drawings, interlock, load and speed, thermal cycles, machining allowances and noise-test conditions.

Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Specify hub preparation, induction heating, casting, thermal treatment and machining. Gear tooth design and drivetrain qualification remain separate from the material-delivery package.

Производственный маршрут

Metal-Core MC Nylon Gear Casting Workflow

Prepare and locate the hub → Condition hub, mold and monomer → Cast and polymerize → Finish and qualify. Define preparation, filling, cure and output timing separately for the selected configuration.

01

Prepare and locate the hub

Confirm material, interlock, surface preparation and positioning.

02

Condition hub, mold and monomer

Review heating and vacuum conditions for the selected construction.

03

Cast and polymerize

Validate filling and thermal behavior at the metal/nylon interface.

Конфигурация процесса

Технические характеристики эталонного решения

Существующая конфигурация и справочные данные испытаний. Настройки оборудования, результаты по материалам и результаты по готовой сборке приведены отдельно; применяйте каждое значение только к его задокументированной конфигурации и условиям.

ПараметрЗначение / единица измеренияПрименимая конфигурация / условия
Continuous Monomer Pour Output3.0 to 20.0 kg/minНепрерывно регулируемая насосная установка на шестерённых насосах высокого давления с сервоприводом
Induction Metal Core Heating Rate160°C ± 2°C in ≤ 60 secondsMedium-frequency induction heating coil under nitrogen
Maximum Transmitted Gear TorqueUp to 4,500 N·mSplined 40Cr steel hub with dovetail mechanical interlock
Gear Meshing Noise AttenuationGreater than or equal to 15 dB(A)Measured vs conventional forged steel gears in closed gearbox
Mold Cavity Pre-Vacuum LevelDown to 1.0 kPa (Absolute)Multi-stage vacuum evacuation skid with tool sealing
Finished Gear Diameter EnvelopeØ 400 mm to Ø 1,200 mmInvolute gear tooth tooling (Module m = 6– 16)
Existing application note: Noise reduction, torque and service life apply to the selected component and test conditions. A metal core is an insert, separate from the liquid chemical feed streams. Original process references, with their existing values: Hub cleanliness Sa 2.5; Induction temp 160°C ± 2°C; confirm for selected material and tooling; Tool temp 165°C; Cavity vacuum ≤ 1.0 kPa; confirm for selected material and tooling; Tank vacuum ≤ 0.01 kPa; Metering accuracy ±0.2%; confirm for selected material and tooling; Flow rate 3.0–20.0 kg/min; Infiltration time < 50 s; confirm for selected material and tooling; In-mold cure 18 min; Transmitted torque up to 4,500 N·m; confirm for selected material and tooling. Supplementary references: tool vacuum 1 kPa absolute, material 135°C, a shot of 18 kg in 45 seconds, polymerization 18 minutes and annealing at 150°C. Validate the gear, hub, material and time boundaries; these settings do not prove a void-free or stress-free interface. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.

Основное оборудование для этого решения

Справочные данные по оборудованию выбираются по документированному для них процессу. Основное дозирование, вспомогательная подача и альтернативные схемы не являются единым стандартным комплексом.

Управление процессом и прикладные проверки

Оцените эти функции с учетом выбранного материала, оснастки и производственного задания. Для результатов готовых деталей требуется отдельное приемочное подтверждение.

Defined metal/nylon interface

Coordinate mechanical retention and thermal preparation without assuming stress-free bonding.

Inspected casting quality

Agree internal/interface inspection instead of using vacuum as proof of no defects.

Comparable drive tests

Evaluate torque and noise on the same gear geometry, speed, load and enclosure baseline.

Связанные проекты

Это справочные данные по родственным применениям. Сравнивайте фактические материалы, процесс и поставленные модули; приведенные показатели проекта не являются приемочными результатами для другой линии.

Смотреть проект
Вопросы планирования

Вопросы и ответы по планированию производства

Подбор, объём поставки и валидация для этого производственного направления.

Does a vacuum-assisted process guarantee torque capacity? +
No. Torque depends on the gear design, hub/interlock, material, processing and service conditions. Test the intended assembly.
How should noise reduction be compared? +
Use a stated steel or other baseline with matched geometry, speed, load, gearbox and measurement method.
Какая информация необходима для предварительной конфигурации? +
Hub/tooth drawings, interlock, load and speed, thermal cycles, machining allowances and noise-test conditions. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

Обсудите ваши производственные задачи

Share the following with your production brief: Hub/tooth drawings, interlock, load and speed, thermal cycles, machining allowances and noise-test conditions. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Связаться с нами

О том, как мы обрабатываем информацию из вашего запроса, читайте в Политика конфиденциальности.

Анализ конфигурации на основе данных о применении и материалах Согласованная документация по оборудованию, интерфейсам и приёмке Обучение и поддержка, определённые для поставляемого комплекта
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube