Проект линии композитных листовых рессор для тяжелых грузовиков в Китае

Equipment configuration and application-specific outcomes reported in the supplied brief for Heavy Truck Composite Leaf Spring Line.

Обзор проекта

Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.

Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.

Конфигурация и результаты проекта, описанные в предоставленной справке по проекту.

A leading national commercial heavy-duty truck manufacturer in Shandong deployed Haifeng’s 3,000-ton active-leveling composite compression press line across its chassis manufacturing plant. The project was commissioned to mass-produce single-leaf parabolic composite leaf springs for front steer axles on next-generation heavy logistics prime movers.

Prior to this installation, the manufacturer utilized multi-leaf 60Si2Mn forged steel springs. The steel spring assemblies added 138 kg of parasitic unsprung mass per vehicle, penalizing fuel efficiency and generating severe inter-leaf frictional squeak. Initial trials with generic compression presses failed because parabolic springs feature extreme thickness tapers (ranging from 18 mm at ends to 65 mm at the center clamping boss). This asymmetric mass created high off-center platen tilting (exceeding 0.35 mm), causing interlaminar thickness variations that failed fatigue testing under 300,000 cycles.

Haifeng engineered a heavy-tonnage compression molding cell centered on the HF-PCM3000-AL platform. Featuring closed-loop four-corner active hydraulic leveling (within ±0.018 mm) and rapid 1.8-second full-pressure ramping, the supplied brief reports processing 68 wt% glass prepreg packs, a front-axle spring assembly mass reduction from 138 kg to 18 kg (120 kg), and 1 million fatigue cycles for the specified spring test configuration.

Концептуальная иллюстрация: Сгенерированная концептуальная иллюстрация для обсуждения процесса; это не фотография указанной машины, предприятия заказчика или реализованного проекта.

Реализация решений

Конфигурация, указанная в предоставленном техническом задании.

Haifeng engineered an automated high-precision compression molding cell tailored for heavy variable-thickness suspension springs. High-strength unidirectional continuous glass fiber epoxy prepreg sheets are cut by automated ultrasonic cutters and stacked by six-axis robots into calibrated parabolic charge packs.

The charge pack transfers into the 3,000-ton press bed via robotic loading grippers, placed precisely inside forged steel tooling heated to 150°C ± 1°C. The press descends at 400 mm/s. Upon initial contact, four high-pressure digital servo cylinders located at the platen corners engage, ramping to full 30,000 kN clamping force in 1.8 seconds.

Real-time optical linear encoders feed position data to the PLC at 1 kHz, correcting platen parallelism to within ±0.018 mm despite severe off-center tipping moments from the thick central boss. The 12.0 MPa cavity pressure forces epoxy through dense roving bundles across a 180-second isothermal cure. Following automated unclamping, bottom ejector pins raise the cured spring for robotic extraction and automated edge-milling, producing finished springs weighing just 18 kg.

ОборудованиеМодельКол-воФункция
3,000-Ton Active-Leveling Composite PressHF-PCM3000-AL1 комплектPrimary 30,000 kN clamping, ±0.02 mm 4-corner active leveling, and 1.8s pressure ramp.
Heavy-Duty Forged Steel Spring ToolingHF-FST-1852 комплектаChrome-plated P20 steel tools with integrated multi-zone electric heating.
Prepreg Automated Stacking & Loading RobotHF-ASR-021 ед.Six-axis robot with needle end-effector transferring thick prepreg charges.
Hydraulic Accumulator High-Speed StationHF-HAS-301 комплектNitrogen-charged accumulators driving fast platen approach and 1.8s pressure ramp.

Заявленные результаты — требуются первичные протоколы

120 kg
Chassis Deadweight Reduction
Reported in the supplied project brief: Per-truck front axle suspension weight dropped from 138 kg (steel) to 18 kg (composite).
1,000,000 Cycles
Fatigue Durability Bench Test
The supplied project brief reports 1,000,000 cycles under QC/T 29035 vertical-loading conditions, with no delamination or stiffness loss observed in the tested spring configuration; this is a part-test result, not a press rating.
± 0.018 mm
Platen Parallelism Tolerance
Reported in the supplied project brief: Active 4-corner dynamic leveling holding platen tilt under full 30,000 kN off-center force.
Концептуальная иллюстрация линии композитных рессор для тяжелых грузовиков

Scale Your Composite Chassis Suspension Production

Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube