Оборудование для дозирования, смешивания и литья смол
128 просмотров

Трёхкомпонентная машина для литья ПУ | Криогенная изоляция

Трёхпоточное дозирование ПУ и динамическое смешивание для разработки криогенной изоляции с отдельным контролем добавок и квалификацией материалов.

Расход на выходе

от 5,0 до 45,0 кг/мин (плавная регулировка)

Соотношение компонентов (A:B:C)

100:110:5 to 100:150:20 (By weight)

Справочная точность

±0,2% (при непрерывном отслеживании массового расхода по Кориолису)

Рабочее давление

0,3–0,6 МПа (дозирующие линии и динамическая смесительная головка)

Наличие по запросу Срок поставки — по предложению Гарантия 1 год
LNG Cargo Containment Barrier Insulation

Deep-Cryogenic Low-Exotherm Polyurethane Casting for LNG Carriers

Трёхпоточное дозирование ПУ и динамическое смешивание для разработки криогенной изоляции с отдельным контролем добавок и квалификацией материалов.

Three-stream PU material preparation, metering and dynamic mixing are configured for cryogenic-insulation development. The primary reactive streams and independent additive feed require their own calibration and material-contact review.

Molds, curing equipment, chemical formulation and finished insulation qualification are specified separately. Cryogenic crack resistance, reaction heat and thermal conductivity depend on the material and specimen conditions.

Концептуальная иллюстрация: Сгенерированная иллюстрация для обсуждения процесса; не фотография указанной машины, объекта заказчика или реализованного проекта.

Deep-Cryogenic Low-Exotherm Polyurethane Casting for LNG Carriers

Поток материалов и принцип работы

Condition the Material Streams

Prepare the primary PU components and the independent additive for the selected insulation formulation.

Calibrate Metering

Check the primary ratio and the separate additive loading under the actual material and operating conditions.

Mix and Fill the Mold

Coordinate dynamic mixing, shot delivery and mold filling with the selected insulation geometry.

Cure and Qualify Samples

Use the specified cure and conditioning procedure, then test representative insulation specimens against the agreed cryogenic requirements.

Нужно коммерческое предложение на это оборудование?

Запросить предложение
Данные конфигурации

Модель и технические параметры

The listed equipment references concern material conditioning, primary-stream metering, independent additive delivery and dynamic mixing. Cryogenic service, material test results and project approvals are separate acceptance requirements.

Технический параметрHF-LNG163-3K
Компоненты3 Streams (A: Base Polyol, B: Polymeric MDI, C: Toughener/Additive)
Диапазон производительностиот 5,0 до 45,0 кг/мин (плавная регулировка)
Диапазон соотношения смешивания100:110:5 to 100:150:20 (By weight)
Справочная точность±0,2% (при непрерывном отслеживании массового расхода по Кориолису)
Электропитание380 В, 3 фазы, 50 Гц (по заказу 440 В/480 В 60 Гц)
Рабочее давление0,3–0,6 МПа (дозирующие линии и динамическая смесительная головка)
Объём бака / бункераTank A: 150 L, Tank B: 150 L, Tank C: 50 L (Stainless 316L)
Масса3,850 kg (Main proportioning skid and mixing station)
Габариты (Д×Ш×В)3600 mm x 2200 mm x 2450 mm
Комплектация оборудования

Ключевые особенности оборудования

Conditioned primary streams, an independent additive feed, dynamic head and controls; molds, curing equipment, approved chemical formulation and final insulation qualification are separate interfaces.

Cryogenic Material Trials

Evaluate the intended formulation and representative insulation specimens under the selected thermal and mechanical test conditions.

Reaction and Cure Coordination

Coordinate shot size, tool conditions and cure with the formulation and insulation thickness. Peak reaction heat is evaluated for that material and geometry.

Independent Additive Delivery

The third feed is calibrated separately from the main component ratio. Select compatible hardware for the actual additive and any suspended particles.

Defined Qualification Interfaces

Equipment supply is coordinated with material, component and project qualification responsibilities. Applicable approvals require the actual scope and supporting documentation.

Обсудите конфигурацию вашего оборудования

Сообщите о вашей продукции, материалах, оснастке и требованиях к производству, чтобы мы могли рассмотреть оборудование и интерфейсы для вашего проекта.

Вопросы планирования

Часто задаваемые вопросы

What is included in the three-stream configuration?
Specify the primary reactive components and the separate additive, with material conditioning, metering, mixing and controls for each stream.
Does a liquid-nitrogen trial establish LNG service approval?
It evaluates a defined specimen and thermal exposure. Long-term service, completed insulation construction and project approval require their own qualification.
How is the additive stream calibrated?
Define its material, target loading, flow range, temperature and measurement method separately from the primary component ratio.
Может ли она подключаться к автоматизированному манипулированию формами?
Review mold transfer, dispensing access, controls and interlocks for the proposed line. Supplied handling and tracking modules are identified in the project scope.

Готовы обсудить ваш проект?

Свяжитесь с нашей командой
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube