Composite PV Frame Direct Injection Solution Banner background

Solución de inyección directa para marcos fotovoltaicos de material compuesto

Coordinate closed-box PU injection and continuous pultrusion for the selected composite PV frame profile.

Planificación de la línea de producción

Engineered Composite Framing for Next-Generation Solar Modules

Continuous frame pultrusion feeds reinforcement through the configured injection box and heated die before pulling and cutting. Resin delivery, reinforcement wet-out, die temperature and pull speed must be matched. This is distinct from molding separate frames in a closed tool or dispensing adhesive around a module.

Alcance de suministro definido

Define resin conditioning, metering, mixing and injection-box interfaces, then identify pulling, heating and cutting equipment. Frame and module performance require their own structural, environmental and electrical evaluation.

Insumos para la selección del proceso

Profile section, fiber form/sizing, resin data, fiber-content basis, die length, puller interfaces and module tests.

Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Define resin conditioning, metering, mixing and injection-box interfaces, then identify pulling, heating and cutting equipment. Frame and module performance require their own structural, environmental and electrical evaluation.

Ruta de producción

Composite PV Frame Direct Injection Workflow

Prepare reinforcement and profile → Condition and meter resin → Impregnate, heat and pull → Cut and qualify. Define preparation, filling, cure and output timing separately for the selected configuration.

01

Prepare reinforcement and profile

Confirm fiber form, sizing, content basis and the profile/die design.

02

Condition and meter resin

Establish resin handling, ratio and the injection-box interface.

03

Impregnate, heat and pull

Validate wet-out and cure along the actual die and line-speed window.

Configuración y parámetros del proceso

Standard Engineering Parameters for Solar Pultrusion

Configuración existente y referencias de ensayo. Los ajustes del equipo, los resultados del material y los resultados del conjunto terminado son independientes; aplique cada valor solo a su configuración y condiciones documentadas.

ParámetroValor / UnidadConfiguración / Condiciones aplicables
Resin Dosing Output0.8 to 8.0 kg/min (Custom up to 15 kg/min)Servo-driven continuous high-pressure piston pumps
Presión de mezcla10.0 to 15.0 MPaHigh-pressure impingement mixing without dynamic rotor
Stoichiometric PrecisionTolerancia de proporción dentro de ±0,3 %Dynamic closed-loop encoder tracking across pull speeds
Pultrusion Line Speed Range0.5 to 1.5 m/min (Standard)Matched to polyurethane resin gelation and die length
Supported Fiber ContentUp to 82% (Fiber volume fraction)High-pressure closed injection box with roving pre-seal
Frame Profile Tensile ModulusGreater than 45 GPaASTM D638 testing on cured glass/polyurethane matrix
Existing application note: Day tank capacities, injection head bracket fixtures, and multi-cavity die boxes are custom-engineered to integrate with existing pultruder machine beds. Values are configuration references and require confirmation under the stated material and operating conditions. Original process references, with their existing values: Fiber volume fraction > 80%; Nitrogen pressure 0.02–0.05 MPa; Temp 35°C; Dynamic ratio tolerance within ±0.3%; Injection pressure 10–15 MPa; Cavity backpressure 1.5 MPa; Pull speed 0.8–1.5 m/min; Die temp up to 195°C. Supplementary references: mixing up to 15 MPa, die temperature 160–195°C and material moisture under 50 ppm. The separate 20% weight comparison belongs to the stated frame/module design. Validate material, die and test records before using these settings or comparisons. The original reinforcement example is 4800tex roving. Confirm fiber form, sizing and die suitability rather than treating this as a universal feed specification. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.
Dosificación, mezcla y equipos de línea

Equipos principales de esta solución

Las referencias de equipos se seleccionan según su proceso documentado. La dosificación principal, el suministro auxiliar y las rutas alternativas no constituyen un único paquete estándar.

Aspectos técnicos a considerar

Controles de proceso y verificaciones de aplicación

Evalúe estas funciones con el material, los moldes y el resumen de producción seleccionados. Los resultados de las piezas acabadas requieren su propia evidencia de aceptación.

Line-linked delivery

Coordinate resin demand with profile geometry and pulling speed.

Separate pressure references

Distinguish mixing pressure, injection delivery and box backpressure.

Verified reinforcement basis

Confirm fiber mass or volume content and use actual wet-out and laminate evidence.

Aplicaciones y proyectos relacionados

Proyectos relacionados

Estas son referencias de aplicación relacionadas. Compare el material, el proceso y los módulos entregados reales; las cifras de proyecto reportadas no son resultados de aceptación para otra línea.

Revisar proyecto
Preguntas sobre planificación de la producción

Preguntas frecuentes

Find answers about Composite PV Frame Direct Injection Solution, including material selection, equipment configuration and the information needed to plan a production line.

Is direct injection here a batch closed-mold process? +
No. Here it supplies the closed impregnation box in a continuous pultrusion route. Batch closed-mold framing is assessed separately.
Does the stated fiber percentage establish laminate quality? +
No. Confirm whether it is mass or volume content, the reinforcement and measurement basis, and the resulting wet-out and void evidence.
¿Qué información se necesita para una configuración preliminar? +
Profile section, fiber form/sizing, resin data, fiber-content basis, die length, puller interfaces and module tests. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

Request a Composite Solar Frame Equipment Proposal

Share the following with your production brief: Profile section, fiber form/sizing, resin data, fiber-content basis, die length, puller interfaces and module tests. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Contáctenos

Para saber cómo tratamos la información de su consulta, lea nuestra Política de privacidad.

Revisión de la configuración basada en la aplicación y los datos del material Documentación acordada de equipo, interfaces y aceptación Formación y soporte definidos para el paquete suministrado
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube