Composite Leaf Spring HP-RTM Molding Solution Banner background

Composite Leaf Spring HP-RTM Molding Solution

HP-RTM systems for thick-section composite leaf springs. The reference project reports 65% lower spring weight and over one million fatigue cycles for its qualified component configuration.

65% Weight Reduction vs Steel Springs
1,000,000+ Dynamic Fatigue Test Cycles
5.0min Thick-Section Demolding Cycle
Chassis Suspension Engineering

Heavy-Duty HP-RTM Solutions for Composite Leaf Springs

Steel leaf springs contribute massive unsprung weight to commercial vehicles and light trucks, negatively impacting ride comfort, fuel efficiency, and payload capacity. Replacing them with continuous glass-fiber reinforced composites can cut weight by up to 65% while providing a smoother, variable-rate suspension response. However, molding leaf springs requires driving resin through extremely thick, densely packed layers of unidirectional fibers. Haifeng’s heavy-duty HP-RTM system utilizes extreme injection pressures and high-capacity vacuum pumps to support controlled resin impregnation through the spring center region, with finished-spring fatigue endurance established through component qualification for the selected design and material. The stated weight reduction compares the reference spring with conventional multi-leaf steel assemblies. Fatigue endurance and internal-defect results apply to the qualified component and test conditions; they are not universal equipment ratings.

Reference Spring: 65% Lower Weight

The referenced project compares its composite suspension spring with conventional multi-leaf steel assemblies. This component result does not establish a 65% reduction in total chassis or vehicle weight.

Reference Fatigue Result: >1M Cycles

The referenced project records over one million dynamic fatigue cycles without observed inter-laminar failure under its bench-test conditions. Qualification follows the actual spring design, laminate and resin; equipment acceptance is separate.

Assess the thick spring section with the actual laminate, resin window and preform. The filling trial should record resin conditions, vacuum, flow progression and complete molding stages, followed by component inspection; it is separate from a prepreg-compression route.

Proceso de fabricación

Composite Leaf Spring HP-RTM Workflow

A four-stage reference workflow coordinating preform preparation, resin delivery, heated cure and component inspection. Internal-defect and fatigue results are checked for the selected spring configuration.

01

Preparación de preformas y vacío

Thick unidirectional glass fiber stacks are loaded into the heavy press; robust vacuum systems pull mold pressure down to <10 mbar

02

Extreme High-Pressure Injection

The HP-RTM unit injects low-viscosity resin at extreme pressures, driving deep matrix penetration through dense fiber cores

03

High-Tonnage Heated Curing

The press clamps firmly to consolidate the thick section while dynamic TCU loops manage exothermic heat dissipation evenly

Configuración y parámetros del proceso

Especificaciones de ingeniería y parámetros técnicos

Parámetros técnicos de este sistema de producción HP-RTM de Haifeng.

Parámetro técnicoEspecificación estándar / ValorContexto de ingeniería y verificación
Aplicación objetivoCommercial Vehicle & Passenger Car Leaf SpringsChassis suspension dynamic shock absorbing
Matriz del materialFast-Curing Epoxy/PU + Unidirectional Glass FiberThick-laminate structural composite system
Part Thickness CapabilityUp to 40 – 60 mm (Center clamping zone)Deep-core high-pressure penetration
Capacidad de dosificación20 – 60 kg/min (personalizable)Bombas de pistón axial servoaccionadas con bloqueo de relación
Fatigue Life Rating>1,000,000 CyclesFinished-spring bench-test reference for the selected design, laminate and resin; not a machine endurance rating
Tiempo de ciclo de desmoldeo240 – 360 seconds (Standard 5 min)High-throughput thick-section processing
Weight ReductionUp to 65% vs. Multi-Leaf Steel SpringsReference spring component versus conventional multi-leaf steel assemblies; not total vehicle weight
Alcance del suministroTurnkey (HP-RTM Skid, Vacuum Skid, TCU + Press/Tooling)Full workcell delivery or press retrofit
Injection pressure ramps, press clamping profiles, and mold core heating zones are customized according to suspension spring thickness and camber curve. Weight reduction and fatigue endurance are finished-spring results, not universal machine ratings. The stated reference figures apply to the selected spring design, laminate, resin and qualification conditions.
Dosificación, mezcla y equipos de línea

HP-RTM Equipment for This Application

The leaf-spring HP-RTM reference coordinates resin delivery with the selected closed tool and press; a prepreg-compression press is a different process package.

Aspectos técnicos a considerar

Ventajas técnicas clave

For Automotive Composite Leaf Spring HP-RTM System, assess material compatibility, process control, equipment interfaces and changeover needs against your production brief.

Reference Spring Weight Reduction

The reference project records 65% lower spring component weight against its conventional multi-leaf steel baseline. Vehicle payload and fuel outcomes require their own assessment.

1,000,000+ Cycles Dynamic Fatigue Life

The project records over one million fatigue cycles under its component bench-test conditions. Laminate quality and endurance are established through inspection and qualification.

Material-Specific Corrosion Assessment

Environmental resistance depends on the laminate, resin and interfaces. It is assessed for the intended exposure conditions rather than treated as complete corrosion immunity.

Superior NVH Ride Comfort

High internal damping of composite materials filters harsh high-frequency chassis vibrations.

Aplicaciones y proyectos relacionados

Proyectos relacionados

The linked spring project gives a design-specific comparison. Keep its laminate, load test and component-weight basis together when assessing another spring.

View Leaf Spring Case Study
Preguntas sobre planificación de la producción

Preguntas frecuentes

Engineering and purchasing questions about this HP-RTM production route.

How can HP-RTM penetrate thick composite parts like leaf springs without dry spots? +
Controlled resin flow, the stated mold vacuum reference (<10 mbar), gate layout and thermal recipes support impregnation before gelation. Pressure alone does not establish complete wet-out; internal defects require component inspection.
Can composite leaf springs really replace heavy steel on commercial vehicles? +
The reference project reports 65% lower spring component weight than its conventional multi-leaf steel baseline and over one million dynamic fatigue cycles under its bench-test conditions. Load-deflection, fatigue, environmental behavior and dimensions are qualified for the selected spring design, laminate and resin; these are not universal machine guarantees.
Can this HP-RTM line integrate with our existing composite press? +
Yes. Haifeng supplies the HP-RTM machine, vacuum skid, and master PLC cabinet with standard fieldbus interfaces (Profibus/EtherCAT) to synchronize seamlessly with your press.
Does Haifeng provide complete turnkey lines including presses and molds? +
Yes. Haifeng offers complete turnkey deliveries, including high-tonnage composite hydraulic presses, high-temperature matched steel tooling, and automated preform handling.
What is the typical installation and commissioning timeline on-site? +
On-site positioning, fluid piping hookup, vacuum calibration, and live composite trial runs are typically completed within 21 days by Haifeng field engineers.
¿Qué datos se necesitan para esta configuración? +
Spring drawing/load case, thickness distribution, fiber preform, resin data, tool gates/vents, existing press and acceptance tests. Identify retained equipment and the required acceptance documents.
What evidence supports impregnation through a thick spring center? +
Use the specified preform and resin in a documented fill/cure trial, then inspect the agreed sections or features. Injection settings alone do not establish wet-out or spring fatigue performance.

Discuss Your HP-RTM Production Project

Share the following for this application: Spring drawing/load case, thickness distribution, fiber preform, resin data, tool gates/vents, existing press and acceptance tests. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Contáctenos

Para saber cómo tratamos la información de su consulta, lea nuestra Política de privacidad.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube