Fondo del banner de Cómo calcular el peso equivalente para formulaciones de poliuretano

Cómo calcular el peso equivalente para formulaciones de poliuretano

Revise los cálculos del peso equivalente de poliol e isocianato, relaciónelos con el índice de isocianato e identifique los errores comunes en los cálculos de formulación de poliuretano.

Unos pocos gramos de error de isocianato por cada 100 partes de poliol pueden convertir un elastómero denso y resistente al desgaste en una pieza que cura lentamente en el centro o que no alcanza la dureza de desmoldeo. En la planta de producción, el problema suele atribuirse a la relación de bombas, a la temperatura del molde o al nivel de catalizador. Antes de cualquiera de esos factores, el primer dato que conviene comprobar es el peso equivalente empleado para construir la fórmula.

El peso equivalente (PE) define cuántos gramos de un material aportan un grupo reactivo. En los sistemas de poliuretano, eso significa gramos por equivalente de hidroxilo en el caso de polioles y extendedores de cadena, y gramos por equivalente de NCO en el caso de isocianatos y prepolímeros. El cálculo es sencillo, pero los pequeños errores se propagan a través del índice de isocianato y de la relación A/B, y luego se manifiestan como contracción, falta de dureza, colapso de la espuma o inestabilidad dimensional.

Muestra de lámina flexible de color pálido sobre una superficie de trabajo de madera

Qué controla el peso equivalente en una receta de PU

El peso equivalente es el puente entre la ficha técnica de una materia prima y una receta de máquina viable. Controla cuatro decisiones prácticas en secuencia:

  • Si la fórmula está químicamente equilibrada antes de que la máquina siquiera arranque.
  • Si el índice de isocianato objetivo es real o solo nominal.
  • Cuántas partes en peso de isocianato deben dosificarse frente al lado del poliol.
  • Si la masa dispensada en cada molde coincide con el peso de inyección para el que se diseñó el útil.

Una formulación puede tener una mezcla excelente, un control de temperatura preciso y una bomba estable. Si el peso equivalente introducido en la receta es incorrecto, la pieza seguirá siendo incorrecta.

Cómo calcular el peso equivalente del poliol

Para los polioles, la conversión estándar se obtiene del índice de hidroxilo (OHV), expresado en mg KOH/g:

Peso equivalente del poliol = 56.100 ÷ índice de hidroxilo [1]

Expresado de forma más directa:

PE del poliol (g/eq) = 56.100 / OHV

El factor 56.100 convierte miligramos de KOH por gramo en equivalentes moleculares. Existe porque la masa molar del KOH es 56,1 g/mol.

Por ejemplo, un triol de poliéter de peso molecular 3.000 con un índice de hidroxilo publicado de 56,1 mg KOH/g tiene:

PE = 56.100 ÷ 56,1 = 1.000 g/eq

Un poliol de menor peso molecular con un índice de hidroxilo de 112,2 mg KOH/g tiene un peso equivalente de 500 g/eq.

For blended polyols, do not average the equivalent weights directly. Calculate the blend equivalent weight from equivalents:

EW blend = 100 ÷ [(parts A ÷ EW A) + (parts B ÷ EW B)]

If a blend contains 80 parts of a 1,000 EW polyol and 20 parts of a 500 EW polyol:

Equivalents = 80 ÷ 1,000 + 20 ÷ 500 = 0.08 + 0.04 = 0.12 equivalent per 100 parts

EW blend = 100 ÷ 0.12 = 833.3 g/eq

Flecha roja hacia arriba sobre una superficie de material marrón texturizado

Cómo calcular el peso equivalente del isocianato

For isocyanates and prepolymers, the starting point is NCO content as a weight percentage:

Isocyanate equivalent weight = 4,200 ÷ %NCO [2]

The more exact conversion uses the NCO group molar mass of 42.02 g/mol:

EW isocyanate (g/eq) = 4,202 / %NCO

Pure MDI with an NCO content of 33.6% therefore has:

EW = 4,202 ÷ 33.6 = 125.1 g/eq

A quasi-prepolymer with 16.0% NCO has:

EW = 4,202 ÷ 16.0 = 262.6 g/eq

For shop-floor work, 4,200 is usually accurate enough. The larger issue is not the conversion factor; it is whether the NCO value being used is current. Prepolymers drift with storage temperature, moisture exposure, and batch age, so the measured NCO from titration should govern critical recipes.

Cómo calcular el índice de isocianato a partir de los pesos equivalentes

Equivalent weights become useful when the isocyanate index is calculated correctly. The index compares actual NCO equivalents to theoretical active-hydrogen equivalents [3]:

Isocyanate index = (actual NCO equivalents ÷ theoretical active-hydrogen equivalents) × 100

Water must be included because one mole of water consumes two NCO groups. Water has a molecular weight of 18 g/mol and two active hydrogens, so its equivalent weight is 9 g/eq.

Consider this simple formulation:

ComponenteParts by weightEquivalent weightEquivalents
Poliol100.01,0000.100
BDO chain extender8.0450.178
Agua0.290.022
Total active hydrogen108.2—0.300

At a 1.05 index with an MDI equivalent weight of 125:

Isocyanate parts = 1.05 × 0.300 × 125 = 39.4 parts

Without the 0.2 parts of water, the same formula would require only about 36.5 parts of MDI. The water looks negligible by weight but adds nearly 3 parts of isocyanate demand. That is exactly where many operator-built spreadsheets drift away from the lab formulation.

Errores que alteran el índice real

Usar el índice de hidroxilo como peso equivalente

A hydroxyl value is not an equivalent weight. A polyol with an OHV of 56 is not 56 g/eq. The correct value is 56,100 ÷ 56, or about 1,002 g/eq. Skipping the 56,100 conversion creates a grossly unbalanced recipe.

Promediar pesos equivalentes sin ponderar

An 800 EW and a 1,000 EW polyol do not necessarily produce a 900 EW blend. The equivalent contributions must be calculated from parts by weight, as shown above. The error grows when one polyol is present at a much higher fraction.

Usar NCO nominal en lugar de NCO medido

A supplier datasheet is a starting point, not a live quality certificate. Moisture ingress during storage can lower effective NCO and shift the true equivalent weight. For tight elastomer or structural foam work, use measured NCO from titration.

Ignorar el agua y la humedad

Water is not just a blowing agent. It is a reactive component with an equivalent weight of 9. Wet polyol, humid filler, or small water additions all consume isocyanate and change the effective index. If the recipe does not account for them, the machine can hold a perfect ratio while the part still comes out soft or friable.

Index errors from equivalent weight mistakes often appear first as dimensional or surface defects. Causas de la contracción en la espuma de poliuretano y cómo controlarla covers the shrinkage mechanisms operators see when the real ratio drifts away from the recipe.

De los cálculos de la receta a la dosificación de la máquina

A correct spreadsheet only matters if the machine reproduces the ratio as mass throughput. The isocyanate parts and polyol parts calculated from equivalent weights become the weight- or volume-based ratio setpoint on the metering system.

In practice, three machine-level factors determine whether the calculation survives contact with production:

  • Metering accuracy. A closed-loop servo or mass-flow system holding ±0.3% full-range accuracy is far more likely to preserve a 1.05 index than an open-loop gear pump subject to viscosity drift.
  • Temperature control. Viscosity change affects flow through fixed orifices, especially when polyol and isocyanate temperatures are not held independently.
  • Recipe integrity. When a line switches from BDO to MOCA, the chain extender equivalent weight changes materially. The machine must switch more than temperatures; it must switch the active mass-flow calibration.

A deviation of one percentage point in the component ratio can shift the effective index enough to produce measurable changes in hardness, cure time, or foam density. The formula does not need to be off by large numbers to create a production problem.

Pasillo de fábrica flanqueado por equipos de procesamiento industrial continuo

Equivalent weight sets the balance; the next calculation is how much of that balanced mixture belongs in each mold. Cómo calcular el peso de dosificación en poliuretano covers cavity volume, overpack, and shot calibration for consistent parts.

Ejemplo resuelto: de la TDS a la relación de dosificación

Assume a rigid foam polyol blend with a reported hydroxyl value of 450 mg KOH/g:

Polyol EW = 56,100 ÷ 450 = 124.7 g/eq

The polymeric MDI reports 31.0% NCO:

Isocyanate EW = 4,202 ÷ 31.0 = 135.5 g/eq

At a target index of 1.10 and 100 parts by weight of polyol:

Isocyanate parts = 1.10 × (100 ÷ 124.7) × 135.5 = 119.5 parts

The machine ratio is therefore 100:119.5 by weight. If the mixing head delivers 150 g/s total output, the A-side and B-side flow rates follow directly from that ratio. This is the difference between a recipe calculated from chemistry and a recipe assembled from trial-and-error memory.

Costuras cosidas en muestras de material similar al cuero de color marrón y claro

¿Necesita ayuda para convertir estas cifras en una receta de dosificación?

Haifeng Polyurethane Machinery works with production teams to convert TDS hydroxyl values, measured NCO, and target indexes into metering settings for low-pressure, high-pressure, and elastomer casting lines. Send the following to info@chinahaifeng.com o WhatsApp +86 13566296633:

  • Polyol and isocyanate TDS or measured OHV/NCO values
  • Target isocyanate index and component temperatures
  • Required shot weight or mold cavity volume
  • Current output target and cycle time

We will help you check the recipe before it reaches the mixing head.

Preguntas frecuentes

¿Puedo calcular el peso equivalente a partir del peso molecular en lugar del índice de hidroxilo?

Yes, if the true functionality is known. Equivalent weight equals molecular weight divided by functionality. This works well for defined diols or triols. Formulated blends may contain monofunctional species or side products, so a measured hydroxyl value is usually more reliable for production recipes.

¿Es 4.200 siempre correcto para el peso equivalente de isocianato?

It is a practical conversion from NCO weight percentage to grams per equivalent. The more exact factor is 4,202 because the NCO group molar mass is 42.02 g/mol. For most shop-floor work, 4,200 is close enough, but the NCO percentage itself should be measured, not assumed.

¿Qué ocurre si introduzco un peso equivalente de poliol incorrecto?

The calculated isocyanate demand changes in direct proportion. If the equivalent weight is entered too high, the recipe will under-dose isocyanate and produce soft, under-cured, or hydrolytically weak parts. If it is entered too low, the recipe will over-dose isocyanate and may create brittleness, excessive exotherm, or higher free-NCO levels.

¿Realmente importa el agua en el cálculo?

Yes. Water has an equivalent weight of 9 because one mole of water supplies two reactive hydrogens. Even 0.2 parts of water in a total formula can require roughly 3 additional parts of MDI per 100 parts of polyol. Ignoring it changes the true index.

¿Cómo se relaciona el peso equivalente con la relación de mezcla A/B?

Equivalent weights plus the target index determine the parts by weight of each component. Those parts become the weight-based ratio setpoint for the metering pumps. The calculation is the same for low-pressure and high-pressure equipment; only the machine’s ability to hold the ratio changes.

Referencias

[1] ASTM D4274-21, Standard Test Method for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols, ASTM International, 2021.

[2] ASTM D2572-19, Método de ensayo estándar para grupos isocianato en materiales de uretano o prepolímeros, ASTM International, 2019.

[3] G. Oertel, Polyurethane Handbook, 2.ª ed., Hanser Publishers, 1994.

Si te interesa, echa un vistazo a estos artículos relacionados:

Dureza Shore A frente a Shore D en poliuretano
Medición de la resiliencia de la espuma de poliuretano: guía práctica de ensayo
RRIM frente a RIM: qué proceso se adapta mejor a tu pieza estructural

Hablemos de tus requisitos de producción de poliuretano

Comparte tu aplicación, sistema de materiales, producción objetivo y requisitos de automatización. El equipo de ingeniería de Haifeng puede ayudarte a revisar las opciones de equipos y líneas de producción. Nuestro equipo responderá en un día hábil. Una vez que los requisitos estén claros, ofrecemos una propuesta preliminar en un plazo de dos días hábiles.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube