قد تؤدي بضعة غرامات من الخطأ في كمية الإيزوسيانات لكل 100 جزء من البوليول إلى تحويل إيلاستومر كثيف ومقاوم للتآكل إلى قطعة تتصلب ببطء في مركزها أو لا تبلغ صلابة فك القالب. وفي أرضية الإنتاج، غالبًا ما يُلقى اللوم على نسبة المضخة أو درجة حرارة القالب أو مستوى المحفز. وقبل أي من ذلك، فإن أول رقم يستحق التحقق هو بيانات الوزن المكافئ المستخدمة في بناء التركيبة.
يحدد الوزن المكافئ (EW) عدد الغرامات من مادة ما التي توفّر مجموعة تفاعلية واحدة. وفي أنظمة البولي يوريثان، يعني ذلك الغرامات لكل مكافئ هيدروكسيل في البوليولات وموضّلات السلسلة، والغرامات لكل مكافئ NCO في الإيزوسيانات والبريوليمرات. والحساب بسيط، لكن الأخطاء الصغيرة تنتقل عبر مؤشر الإيزوسيانات ونسبة A/B، ثم تظهر على شكل انكماش أو صلابة غير محققة أو انهيار الرغوة أو عدم استقرار أبعادي.

ما الذي يتحكم فيه الوزن المكافئ في وصفة PU
الوزن المكافئ هو الجسر بين صحيفة بيانات المادة الخام ووصفة تشغيلية صالحة للآلة. وهو يتحكم بأربعة قرارات عملية بالتتابع:
- ما إذا كانت التركيبة متوازنة كيميائيًا قبل أن تبدأ الآلة بالعمل أصلًا.
- ما إذا كان مؤشر الإيزوسيانات المستهدف حقيقيًا أم اسميًا فقط.
- كم عدد الأجزاء بالوزن من الإيزوسيانات التي يجب قياسها مقابل جانب البوليول.
- ما إذا كانت الكتلة المقذوفة في كل قالب تطابق وزن القذفة الذي صُمم القالب من أجله.
قد تتمتع التركيبة بخلط ممتاز وتحكم دقيق في درجة الحرارة ومضخة مستقرة. لكن إذا كان الوزن المكافئ المُدخل في التركيبة خاطئًا، فستبقى القطعة خاطئة.
كيفية حساب الوزن المكافئ للبوليول
بالنسبة إلى البوليولات، يأتي التحويل القياسي من قيمة الهيدروكسيل (OHV) معبّرًا عنها بوحدة mg KOH/g:
الوزن المكافئ للبوليول = 56,100 ÷ قيمة الهيدروكسيل [1]
وبصياغة أكثر مباشرة:
EW للبوليول (g/eq) = 56,100 / OHV
يحوّل المعامل 56,100 مليغرامات KOH لكل غرام إلى مكافئات جزيئية. وهو موجود لأن الكتلة المولية لـ KOH هي 56.1 g/mol.
على سبيل المثال، ثلاثيول بولي إيثر بوزن جزيئي 3,000 وقيمة هيدروكسيل منشورة تبلغ 56.1 mg KOH/g يكون له:
EW = 56,100 ÷ 56.1 = 1,000 g/eq
البوليول بوزن جزيئي أقل وقيمة هيدروكسيل تبلغ 112.2 mg KOH/g له وزن مكافئ قدره 500 g/eq.
بالنسبة إلى البوليولات المخلوطة، لا تحسب متوسط الأوزان المكافئة مباشرة. احسب الوزن المكافئ للخليط من المكافئات:
EW للخليط = 100 ÷ [(الأجزاء A ÷ EW A) + (الأجزاء B ÷ EW B)]
إذا كان الخليط يحتوي على 80 جزءًا من بوليول بوزن مكافئ 1,000 و20 جزءًا من بوليول بوزن مكافئ 500:
المكافئات = 80 ÷ 1,000 + 20 ÷ 500 = 0.08 + 0.04 = 0.12 مكافئ لكل 100 جزء
الوزن المكافئ للمزيج = 100 ÷ 0.12 = 833.3 غ/مكافئ

كيفية حساب الوزن المكافئ للإيزوسيانات
بالنسبة للإيزوسيانات والبوليولات الأولية (البريبوليمرات)، فإن نقطة البداية هي محتوى NCO كنسبة مئوية وزنية:
الوزن المكافئ للإيزوسيانات = 4,200 ÷ %NCO [2]
يستخدم التحويل الأكثر دقة الكتلة المولية لمجموعة NCO البالغة 42.02 غ/مول:
الوزن المكافئ للإيزوسيانات (غ/مكافئ) = 4,202 / %NCO
وبالتالي فإن MDI النقي الذي يحتوي على محتوى NCO بنسبة 33.6% له:
الوزن المكافئ = 4,202 ÷ 33.6 = 125.1 غ/مكافئ
البريبوليمر شبه التام الذي يحتوي على 16.0% NCO له:
الوزن المكافئ = 4,202 ÷ 16.0 = 262.6 غ/مكافئ
بالنسبة للعمل في ورشة الإنتاج، عادةً ما يكون 4,200 دقيقًا بما يكفي. المشكلة الأكبر ليست في معامل التحويل؛ بل فيما إذا كانت قيمة NCO المستخدمة حديثة. تتغير البريبوليمرات مع درجة حرارة التخزين والتعرض للرطوبة وعمر الدفعة، لذا يجب أن تحكم قيمة NCO المقاسة بالمعايرة الوصفات الحرجة.
حساب مؤشر الإيزوسيانات من الأوزان المكافئة
تصبح الأوزان المكافئة مفيدة عندما يُحسب مؤشر الإيزوسيانات بشكل صحيح. يقارن المؤشر المكافئات الفعلية لـ NCO بالمكافئات النظرية للهيدروجين النشط [3]:
مؤشر الإيزوسيانات = (مكافئات NCO الفعلية ÷ المكافئات النظرية للهيدروجين النشط) × 100
يجب تضمين الماء لأن مولًا واحدًا من الماء يستهلك مجموعتي NCO. تبلغ الكتلة الجزيئية للماء 18 غ/مول وله هيدروجينان نشطان، لذا فإن وزنه المكافئ هو 9 غ/مكافئ.
خذ بعين الاعتبار هذه التركيبة البسيطة:
| المكوّن | الأجزاء بالوزن | الوزن المكافئ | المكافئات |
|---|---|---|---|
| البوليول | 100.0 | 1,000 | 0.100 |
| موسّع السلسلة BDO | 8.0 | 45 | 0.178 |
| الماء | 0.2 | 9 | 0.022 |
| Total active hydrogen | 108.2 | — | 0.300 |
At a 1.05 index with an MDI equivalent weight of 125:
Isocyanate parts = 1.05 × 0.300 × 125 = 39.4 parts
Without the 0.2 parts of water, the same formula would require only about 36.5 parts of MDI. The water looks negligible by weight but adds nearly 3 parts of isocyanate demand. That is exactly where many operator-built spreadsheets drift away from the lab formulation.
الأخطاء التي تغيّر المؤشر الفعلي
استخدام قيمة الهيدروكسيل كوزن مكافئ
A hydroxyl value is not an equivalent weight. A polyol with an OHV of 56 is not 56 g/eq. The correct value is 56,100 ÷ 56, or about 1,002 g/eq. Skipping the 56,100 conversion creates a grossly unbalanced recipe.
حساب متوسط الأوزان المكافئة دون ترجيح
An 800 EW and a 1,000 EW polyol do not necessarily produce a 900 EW blend. The equivalent contributions must be calculated from parts by weight, as shown above. The error grows when one polyol is present at a much higher fraction.
استخدام NCO الاسمي بدلاً من NCO المقاس
A supplier datasheet is a starting point, not a live quality certificate. Moisture ingress during storage can lower effective NCO and shift the true equivalent weight. For tight elastomer or structural foam work, use measured NCO from titration.
تجاهل الماء والرطوبة
Water is not just a blowing agent. It is a reactive component with an equivalent weight of 9. Wet polyol, humid filler, or small water additions all consume isocyanate and change the effective index. If the recipe does not account for them, the machine can hold a perfect ratio while the part still comes out soft or friable.
Index errors from equivalent weight mistakes often appear first as dimensional or surface defects. أسباب الانكماش في رغوة البولي يوريثان وكيفية التحكم فيه covers the shrinkage mechanisms operators see when the real ratio drifts away from the recipe.
من حسابات الوصفة إلى قياس الجرعات بالماكينة
A correct spreadsheet only matters if the machine reproduces the ratio as mass throughput. The isocyanate parts and polyol parts calculated from equivalent weights become the weight- or volume-based ratio setpoint on the metering system.
In practice, three machine-level factors determine whether the calculation survives contact with production:
- دقة قياس الجرعات. A closed-loop servo or mass-flow system holding ±0.3% full-range accuracy is far more likely to preserve a 1.05 index than an open-loop gear pump subject to viscosity drift.
- Temperature control. Viscosity change affects flow through fixed orifices, especially when polyol and isocyanate temperatures are not held independently.
- Recipe integrity. When a line switches from BDO to MOCA, the chain extender equivalent weight changes materially. The machine must switch more than temperatures; it must switch the active mass-flow calibration.
A deviation of one percentage point in the component ratio can shift the effective index enough to produce measurable changes in hardness, cure time, or foam density. The formula does not need to be off by large numbers to create a production problem.

Equivalent weight sets the balance; the next calculation is how much of that balanced mixture belongs in each mold. كيفية حساب وزن القذفة في البولي يوريثان covers cavity volume, overpack, and shot calibration for consistent parts.
مثال عملي: من TDS إلى نسبة الجرعات
Assume a rigid foam polyol blend with a reported hydroxyl value of 450 mg KOH/g:
Polyol EW = 56,100 ÷ 450 = 124.7 g/eq
The polymeric MDI reports 31.0% NCO:
Isocyanate EW = 4,202 ÷ 31.0 = 135.5 g/eq
At a target index of 1.10 and 100 parts by weight of polyol:
Isocyanate parts = 1.10 × (100 ÷ 124.7) × 135.5 = 119.5 parts
The machine ratio is therefore 100:119.5 by weight. If the mixing head delivers 150 g/s total output, the A-side and B-side flow rates follow directly from that ratio. This is the difference between a recipe calculated from chemistry and a recipe assembled from trial-and-error memory.

هل تحتاج إلى مساعدة في تحويل هذه الأرقام إلى وصفة جرعات؟
Haifeng Polyurethane Machinery works with production teams to convert TDS hydroxyl values, measured NCO, and target indexes into metering settings for low-pressure, high-pressure, and elastomer casting lines. Send the following to info@chinahaifeng.com أو عبر WhatsApp +86 13566296633:
- Polyol and isocyanate TDS or measured OHV/NCO values
- Target isocyanate index and component temperatures
- Required shot weight or mold cavity volume
- Current output target and cycle time
We will help you check the recipe before it reaches the mixing head.
الأسئلة الشائعة
هل يمكنني حساب الوزن المكافئ من الوزن الجزيئي بدلاً من قيمة الهيدروكسيل؟
Yes, if the true functionality is known. Equivalent weight equals molecular weight divided by functionality. This works well for defined diols or triols. Formulated blends may contain monofunctional species or side products, so a measured hydroxyl value is usually more reliable for production recipes.
هل 4,200 صحيح دائمًا للوزن المكافئ للإيزوسيانات؟
It is a practical conversion from NCO weight percentage to grams per equivalent. The more exact factor is 4,202 because the NCO group molar mass is 42.02 g/mol. For most shop-floor work, 4,200 is close enough, but the NCO percentage itself should be measured, not assumed.
ماذا يحدث إذا أدخلت الوزن المكافئ الخاطئ للبوليول؟
The calculated isocyanate demand changes in direct proportion. If the equivalent weight is entered too high, the recipe will under-dose isocyanate and produce soft, under-cured, or hydrolytically weak parts. If it is entered too low, the recipe will over-dose isocyanate and may create brittleness, excessive exotherm, or higher free-NCO levels.
هل يؤثر الماء فعلاً في الحساب؟
Yes. Water has an equivalent weight of 9 because one mole of water supplies two reactive hydrogens. Even 0.2 parts of water in a total formula can require roughly 3 additional parts of MDI per 100 parts of polyol. Ignoring it changes the true index.
كيف يرتبط الوزن المكافئ بنسبة الخلط A/B؟
Equivalent weights plus the target index determine the parts by weight of each component. Those parts become the weight-based ratio setpoint for the metering pumps. The calculation is the same for low-pressure and high-pressure equipment; only the machine’s ability to hold the ratio changes.
المراجع
[1] ASTM D4274-21، Standard Test Method for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols، ASTM International, 2021.
[2] ASTM D2572-19، طريقة الاختبار القياسية لمجموعات الإيزوسيانات في مواد اليوريثان أو البوليمرات المسبقة، الجمعية الأمريكية للاختبار والمواد (ASTM International)، 2019.
[3] G. Oertel، Polyurethane Handbook، الطبعة الثانية، Hanser Publishers، 1994.
إذا كنت مهتمًا، فاطّلع على هذه المقالات ذات الصلة:
صلابة Shore A مقابل Shore D في البولي يوريثان
قياس مرونة رغوة البولي يوريثان: دليل اختبار عملي
RRIM مقابل RIM: أي عملية تناسب الجزء الإنشائي لديك



