Проект линии основы микрофибровой кожи на водной основе в Китае
Project reference: Water-Borne Microfiber Leather Base Line. Configuration and reported outcomes require original project records.
Обзор проекта
Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.
Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.
A leading publicly listed synthetic leather enterprise in Anhui deployed Haifeng’s water-borne polyurethane mechanical foaming line across its flagship eco-material manufacturing campus. The project was commissioned to supply zero-solvent, highly breathable microfiber leather bases for global athletic footwear and sustainable automotive seating.
Prior to this installation, the manufacturer operated conventional wet-process coagulation lines using dimethylformamide (DMF). This legacy process required massive steam boilers for solvent distillation, produced hazardous wastewater, and left trace solvent residues inside finished leather that breached international Zero Discharge of Hazardous Chemicals (ZDHC) standards. Attempts with chemical blowing agents caused excessive toxic formamide decomposition residues, failing customer brand audits.
Haifeng engineered a complete physical mechanical foaming cell centered on the HF-WPF160-MF system. By whipping compressed air directly into water-borne polyurethane dispersions and stabilizing the cellular structure via infrared flash gelation, the line eliminated solvents and chemical blowing agents entirely, delivering breathable bases reaching 1,520 g/(m²·24h) breathability and cutting utility thermal energy by 45%.
Ограничения данных: This route mechanically disperses gas in a water-borne dispersion; it differs from reactive chemical blowing. Wet-foam gas ratio and final dry density are distinct. MVTR, odor and steam savings need specimen, method and full-line energy boundaries; water-borne chemistry alone does not establish zero emissions.
Концептуальная иллюстрация: Сгенерированная концептуальная иллюстрация для обсуждения процесса; это не фотография указанной машины, предприятия заказчика или реализованного проекта.
Реализация решений
Конфигурация, указанная в предоставленном техническом задании.
Haifeng engineered an automated roll-to-roll mechanical foaming line spanning 32 meters in length. Nonwoven microfiber fleece substrates are unwound through tension-isolated accumulators and pass through a corona surface-activation station to ensure coating anchor strength.
Water-borne polyurethane dispersion (52% solids) blended with silicone foam stabilizers is fed via progressive cavity pumps into an axial multi-tooth stator-rotor foaming head running at 850 RPM. Filtered dry compressed air is injected via mass flow controllers, expanding the resin into a dense 3.5x liquid foam with micro-pore diameters of 15 to 25 µm.
The foam is distributed across a precision floating-knife coater, applying a uniform 0.8 mm layer across the 1,480 mm web width. The wet profile immediately passes under short-wave infrared quartz lamps that flash-skin the foam surface within 8 seconds, preventing pore collapse. The coated web then traverses a 24-meter five-zone convection drying tunnel (85°C to 135°C), evaporating moisture progressively to yield a flexible, fully crosslinked leather base before edge-trimming and automated rewinding.
This route mechanically disperses gas in a water-borne dispersion; it differs from reactive chemical blowing. Wet-foam gas ratio and final dry density are distinct. MVTR, odor and steam savings need specimen, method and full-line energy boundaries; water-borne chemistry alone does not establish zero emissions.
| Оборудование | Модель | Кол-во | Функция |
|---|---|---|---|
| Water-Borne Mechanical Foaming Generator | HF-WPF160-MF | 1 комплект | Core gas-liquid mass dosing and high-shear stator-rotor mechanical foaming. |
| Precision Floating-Knife Coating Station | HF-FKC-1600 | 1 ед. | High-precision micrometric knife spreading foam across 1,480 mm web. |
| Infrared Rapid Flash Pre-Gelation Tunnel | HF-IRG-06 | 1 комплект | Short-wave quartz lamps flash-skinning foam within 8s to prevent collapse. |
| 24-Meter 5-Zone Convection Drying Tunnel | HF-CDT-24M | 1 комплектная линия | Step-down hot air tunnel evaporating water progressively up to 135°C. |
Связанные семейства оборудования
Ссылки на каталог описывают связанные семейства оборудования. Поставленная модель, вспомогательное оборудование и условия приемки определяются конфигурацией проекта.
Заявленные результаты — требуются первичные протоколы

Transition to Zero-Emission Water-Borne Leather Bases
Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.
