Проект модернизации пултрузии композитных фотоэлектрических рам в Китае

Equipment configuration and application-specific outcomes reported in the supplied brief for Composite PV Frame Pultrusion Upgrade.

Обзор проекта

Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.

Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.

Конфигурация и результаты проекта, описанные в предоставленной справке по проекту.

A leading tier-one solar module component manufacturer deployed Haifeng’s automated closed direct-injection pultrusion technology to upgrade its composite photovoltaic frame manufacturing facilities. The project targeted replacing conventional aluminum frame extrusion lines with an advanced, non-corrosive polyurethane fiberglass composite framing process.

Before the upgrade, the customer's experimental pultrusion line utilized open liquid resin baths. This setup suffered from erratic wet-out at line speeds above 0.8 m/min, resulting in internal voids exceeding 3.5% and frequent resin gelation skinning, which required frequent line shutdowns and caused hazardous workshop fumes.

Haifeng supplied an integrated direct-injection package centered on the HF-PVI-40H system. By docking the high-pressure impingement mixing head directly to a sealed die injection chamber, the supplied brief reports processing of 80% fiber-volume bundles at 1.2 m/min. Frame/profile results and solar-module qualification are assessed separately.

Реализация решений

Конфигурация оборудования, приведённая в предоставленной справке по проекту.

Haifeng engineered a fully enclosed resin delivery and wet-out system integrated into the customer’s existing multi-cavity pultrusion line. Raw polyol and isocyanate are stored in dual-jacketed stainless steel vessels with dry nitrogen blankets to prevent moisture-induced foaming.

The chemical components are accurately displaced by servo-driven high-pressure axial piston pumps. Continuous mass flow signals dynamically synchronize with the pultrusion haul-off drive, maintaining stoichiometric consistency within ±0.3% during line acceleration and deceleration.

The chemicals impinge at 12.0 MPa within the die-mounted mixing head and discharge directly into the sealed injection die box. The fast-reacting polyurethane is forced deep into dense bundles of continuous roving (4800tex) under 1.5 MPa hydraulic die backpressure. The saturated profile cures through three progressive electric die heating zones (160°C to 195°C) before passing through automated inline cutting saws for palletizing.

ОборудованиеМодельКол-воФункция
Direct Pultrusion Injection MachineHF-PVI-40H2 комплектаCore nitrogen-blanketed storage, servo metering, and high-pressure impingement injection.
Sealed Multi-Cavity Injection Die BoxHF-IDB-352 шт.Mounts directly to pultrusion die entry, sealing roving under 1.5 MPa backpressure.
Line Speed Dynamic Encoder Sync KitHF-LES-012 комплектаTracks pultruder track speed and modulates servo pump displacements in real time.
Nitrogen Blanketing Control SkidHF-N2-051 ед.Maintains positive dry nitrogen pressure over chemical vessels to prevent moisture entry.

Заявленные результаты проекта — ожидается подтверждение документами

80%
Fiber Volume Fraction
Reported in the supplied project brief: Achieved dense structural fiber packing, raising profile tensile modulus above 45 GPa.
< 0.5%
Internal Micro-Void Rate
The supplied brief reports internal micro-void content below 0.5%, compared with 3.5% for the earlier open-bath process. Quantitative void measurement and ultrasonic inspection are separate evidence.
1.2 m/min
Continuous Line Pull Speed
Reported in the supplied project brief: Stable multi-shift pultrusion output, up from a previous baseline of 0.8 m/min.

Upgrade to High-Efficiency Composite PV Frame Manufacturing

Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube