Проект вспенивания дверей холодильных камер CA в Китае
Project reference: CA Cold Room Door Foaming Project. Configuration and reported outcomes require original project records.
Обзор проекта
Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.
Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.
A leading cold chain logistics equipment and industrial door group in Eastern China deployed Haifeng’s heavy-duty discontinuous door foaming line. The installation was commissioned to manufacture high-performance, extra-thick (220 mm) airtight sliding doors for a major 50,000-ton agricultural controlled-atmosphere (CA) cold storage facility.
Prior to this installation, the client utilized legacy low-pressure single-point dispensing equipment. Injecting 75 kg of resin across an oversized 3.5 m x 2.2 m x 0.22 m panel took over 65 seconds, allowing the leading edge of the chemical front to cream and crosslink before the cavity was filled. This created internal weld lines and severe exothermic core shrinkage. When deployed under -30°C freezer operations, the finished doors bowed inwards by up to 15 mm, causing perimeter rubber gaskets to unseat and resulting in costly air infiltration and icing.
Haifeng engineered a complete heavy-section foaming cell centered on the HF-CRD250-LP system. Featuring synchronized dual-head staggered high-pressure injection and a 200-ton heated hydraulic clamping press, the line eliminated flow knit lines, achieving a 95.5% closed-cell structure and holding low-temperature dimensional shrinkage under 0.42%.
Ограничения данных: The model suffix LP does not identify its pressure class: the supplied circuit is 15–17.5 MPa high-pressure impingement. A 75 kg shot in 18.2 s implies 247.3 kg/min, exceeding the stated combined 180 kg/min maximum; reconcile shot mass, time and head aggregation. Injection time differs from mold dwell and full cure.
Концептуальная иллюстрация: Сгенерированная концептуальная иллюстрация для обсуждения процесса; это не фотография указанной машины, предприятия заказчика или реализованного проекта.
Реализация решений
Конфигурация, указанная в предоставленном техническом задании.
Haifeng engineered an automated heavy-panel discontinuous production cell featuring sequential fluid displacement. Pre-assembled 220 mm door shells incorporating welded internal frame reinforcements and heating wires are transferred onto the preheated lower platen of a 200-ton hydraulic press.
Chemical components—high-density rigid polyol and polymeric isocyanates—are conditioned in dual 300 L jacketed tanks at 22°C. The HF-CRD250-LP unit displaces chemicals at 16.5 MPa via servo-driven axial piston pumps under continuous Coriolis mass flow measurement.
Twin high-pressure impingement mixing heads engage the door’s dual fill ports. The master controller executes a staggered timing sequence, initially injecting at the primary door base before triggering the second head to flood the upper panel, discharging 75 kg of resin within 18 seconds.
The hydraulic press maintains 1.5 bar counter-pressure across the platens, while 45°C water circulation ensures even expansion. The door cures in-mold for 22 minutes to relieve core reaction stresses. Upon demolding, finished doors exhibit verified warpage deviations of less than 1.2 mm across the 3.5-meter length.
The model suffix LP does not identify its pressure class: the supplied circuit is 15–17.5 MPa high-pressure impingement. A 75 kg shot in 18.2 s implies 247.3 kg/min, exceeding the stated combined 180 kg/min maximum; reconcile shot mass, time and head aggregation. Injection time differs from mold dwell and full cure.
| Оборудование | Модель | Кол-во | Функция |
|---|---|---|---|
| Heavy-Duty Door Foaming Machine | HF-CRD250-LP | 1 комплект | Core chemical conditioning, servo metering, and twin-head staggered injection. |
| 200-Ton Heated Hydraulic Door Press | HF-HDP-200 | 1 ед. | Heavy-duty press resisting 1.5 bar foaming pressure for 250 mm thick panels. |
| Multi-Zone Press Water Temperature Unit | HF-WTU-45 | 1 комплект | Dual-circuit tempered water unit holding platen temperatures at 45°C ± 1°C. |
| Infeed/Outfeed Motorized Transfer Bed | HF-MTB-35 | 1 ед. | Heavy roller conveyor facilitating ergonomic loading of 3.5m door shells. |
Связанные семейства оборудования
Ссылки на каталог описывают связанные семейства оборудования. Поставленная модель, вспомогательное оборудование и условия приемки определяются конфигурацией проекта.
Заявленные результаты — требуются первичные протоколы

Upgrade Your Industrial Cold Storage Door Manufacturing
Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.
