Примеры проектов

Проект линии для композитных солнечных рам BIPV в Китае

Equipment configuration and application-specific outcomes reported in the supplied brief for BIPV Composite Solar Frame Line. Banner: generated concept illustration, not a photograph of a delivered project.

Обзор проекта

Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.

Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.

Конфигурация и результаты проекта, описанные в предоставленной справке по проекту.

В предоставленной сводке описан следующий контекст проекта.

A leading integrated renewable energy module manufacturer in Sichuan partnered with Haifeng to upgrade its composite framing infrastructure for shingled BIPV (Building-Integrated Photovoltaics) solar modules. The project was commissioned to supply high-strength, architecturally colored composite frames matching regional building facade codes without secondary spray painting.

Previously, the client outsourced pultruded profiles for manual offline sanding and liquid fluorocarbon painting. This secondary chain added over 20% to profile processing expenses, created volatile organic compound (VOC) compliance liabilities, and suffered from transport chipping. Worse, accelerated climatic aging revealed severe color fading (Δ E > 3.5) after just 24 months of outdoor exposure, threatening major municipal facade contracts.

Haifeng deployed an in-line co-extrusion framing line centered on the HF-PVI50-UV platform. By integrating mold-exit liquid aspartic topcoating with continuous polyurethane fiberglass pultrusion, the line produced monolithic terracotta-colored profiles with a 50 µm bonded protective skin, with the supplied brief reporting Δ E < 1.0 for its exposure/color-measurement conditions and a 22% per-meter cost comparison. These profile results do not independently establish solar-module qualification.

Концептуальная иллюстрация: Generated process visualization, not a photograph of delivered equipment, a customer facility or a completed project.

Реализация решений

Заявленная конфигурация оборудования из предоставленной сводки:

Haifeng engineered and commissioned an in-line dual-resin pultrusion cell that integrates core composite forming with architectural surface finishing. Structural E-glass roving bundles (4800tex) receive fast-curing polyurethane through a 12.0 MPa metering/mixing circuit and a separately controlled closed injection box before advancing through multi-zone steel heating dies (160°C).

Mounted directly to the exit face of the pultrusion tool is a secondary co-extrusion die block. As the fully cured, hot composite profile emerges, the HF-PVI50-UV co-extrusion metering unit delivers aliphatic polyaspartic resin blended with inorganic terracotta red colorant at 14.0 MPa.

The liquid aspartic mixture wraps the 150°C profile in a 50 µm continuous veil, chemically fusing with residual reactive sites on the polyurethane matrix before entering a 1.5-meter non-contact air-chilling tunnel. Reciprocating pullers grip the scratch-resistant profile (4H hardness) at 1.2 m/min, advancing it to high-precision flying saws. The entire offline spray paint shop was completely decommissioned, replacing the specified offline paint-baking and solvent-handling operations. Site emissions remain formulation- and control-dependent.

ОборудованиеМодельКол-воФункция
In-Line Aspartic Co-Extrusion Pultrusion UnitHF-PVI50-UV2 комплектаCore structural pultrusion injection and in-line polyaspartic co-extrusion.
Die-Mounted Precision Co-Extrusion BlockHF-CEB-352 шт.Precision slotted manifold applying 50 µm uniform skin at tool exit.
Multi-Channel Servo Colorant StationHF-SCS-042 шт.Continuous micro-metering of architectural color pigments at ±0.1% accuracy.
Non-Contact Profile Air-Chilling TunnelHF-ACT-152 комплектаRapid convective cooling consolidating 4H surface hardness prior to pulling.

Заявленные результаты — записи ожидают проверки

Δ E < 1.0
UV Color Degradation
The supplied brief reports ΔE 0.78 on 20 batches under its stated Xenon/UV exposure and color-measurement conditions. This is not a standalone machine or coating IEC certificate.
22%
Per-Meter Production Cost Cut
The supplied brief reports 22.4% savings for 100,000 m against 8.5 RMB/m outsourced processing. The comparison applies to its stated material, scrap, finishing and cost boundaries.
4H
Scratch Pencil Hardness
Reported 4H after 24-hour conditioning using a pencil-hardness procedure. This is a categorical hardness result, not a multiple of scratch resistance.

Scale Your Architectural BIPV Frame Manufacturing

Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube