Менеджер по производству заказывает пеногенераторную машину для полиуретана производительностью 15 кг/мин, потому что суточная норма ровно делится на восемь часов. Машина прибывает, и на первой реальной задаче линия либо переполняет маленькие формы на холостом ходу, либо ждёт выдержки в форме, пока смесительная головка остаётся горячей. Проблема была не в операторе, а в том, что подбор делался по номинальной производительности, а не по требуемой массе заливки и циклу.
Подбор производительности — это не одно число. Это цепочка: объём полости, масса заливки, доступное время заливки, время выдержки в форме, коэффициент регулирования и технологическое давление. Это руководство проходит по этой цепочке в том порядке, в котором производственный инженер действительно должен выполнять расчёт.

Номинальная производительность — это не ваша фактическая производительность
Номинальная производительность пеногенераторной машины — это максимальная подача материала при эталонных условиях: заданном давлении, вязкости жидкости, температуре, длине шланга и смесительной головке. Она говорит о том, что могут перекачать насос и смесительная головка, а не о том, сколько будет выпускать ваша линия.
Production rate is lower because material recirculates, molds index, parts cure, cleaning cycles interrupt flow, and operators stop for visual checks. A machine rated at 10 kg/min will not deliver 10 kg of finished foam per minute. The gap between nominal output and usable output is the section you have to size around.
When comparing machines, ask for output in grams per second at your working pressure and viscosity, not a single kg/min figure quoted at ideal conditions. That narrower number is the usable output window, and it determines whether short shots stay repeatable.
Начинайте с массы заливки, а не с характеристик машины
The first sizing number should come from the part:
- Shot weight (g) = cavity volume (cm³) × required molded density (g/cm³)
For a sole cavity of 350 cm³ molded at 0.5 g/cm³, the target shot is about 175 g. For a rail pad or an automotive buffer block, the same calculation runs from the specific cavity and the density the specification requires. Molded density is measured to the relevant product standard, such as ASTM D1622 for rigid foams [1] or ISO 845 for cellular materials [2].
If your largest shot is 175 g, a machine that only holds stable metering above 800 g is the wrong machine. You will spend every shift fighting overpacking, density shift, and flash. The most important number on a short-shot line is often the lowest repeatable shot weight, not the maximum output on the nameplate.
Calculating shot weight from cavity geometry and target density is the first sizing step. Как рассчитать массу впрыска в полиуретане covers the formula with fixture-specific examples.

Отталкивайтесь от времени цикла и времени выдержки в форме
After shot weight, convert it into required pour rate using the production cycle.
A rotary line or carousel does not give you the full station time for pouring. Part of that time belongs to cream and rise, cure open time, demold, mold closing, and index. If a station cycle is 18 seconds, the practical pour window may be only 3 to 5 seconds. If you assume the full 18 seconds are available, you will under-size the machine.
For a 175 g shot poured in 4 seconds, the required flow is about 44 g/s per cavity. If the station holds four cavities, peak demand jumps to roughly 175 g/s, plus a flow margin for restart and line pauses. The machine must hit that peak without leaving the low end of its range unused on smaller jobs.
Demold time matters as much as pour time. A machine sized for a 3-minute cure can sit idle if the part actually needs 5 minutes to reach green strength. Output planning therefore works from the slowest station in the line, not from the mixing head’s best-case moment.
Pour rate is only part of the cycle; the material must rise and fill inside the mold’s working window. Роль времени подъёма в пенообразовании полиуретана covers rise time measurement and mold filling behavior.
Точность дозирования и диапазон регулирования определяют, имеет ли значение цифра производительности
Maximum flow is easy to advertise; turndown is harder to deliver. Turndown describes the ratio between the highest and lowest output at which a machine still maintains component ratio and homogeneous mixing [3]. A machine that can push 15 kg/min but loses ratio control below 2 kg/min is too large for a line that runs 600 g shots.
For polyurethane processing, ratio error at low flow changes density, hardness, and final part quality. Machine design, pump selection, and mixing head volume all influence where ratio starts to drift. That is why you should evaluate the smallest shot you actually run, not the largest shot the pump can deliver [4].
In equipment specifications, look for full-range metering accuracy rather than a single-point accuracy at high flow. For example, a machine may state ±0.3% dynamic metering across its working range. That range is the machine’s true operating band. Above it, the pump is only a number; below it, the shot becomes uncontrolled.
The practical rule is to select the smallest machine whose top end still covers the worst-case peak pour with a reasonable margin. Oversizing “for the future” often sacrifices the present short-shot consistency.

Производительность низкого и высокого давления: две разные логики подбора
Low-pressure and high-pressure machines fail differently when mis-sized, so they require different output thinking.
Low-pressure open-pour machines are usually continuous or large-shot systems. They suit box foam, slabstock, large insulation panels, and open-mold filling. Here output is best evaluated in kg/min at the working pressure and mixture viscosity, because the machine runs for minutes, not fractions of a second.
High-pressure impingement machines are shot-oriented. They rely on rapid, high-energy mixing inside a self-cleaning head and are used for short-cycle molded parts such as soles, steering wheels, and automotive seats. High impingement mixing supports rapid multi-component combination, but the useful output is best evaluated as repeatable shot weight against available pour time [4]. A machine rated at 400 g/s may pour 100 g badly if the turndown is poor; a smaller machine rated at 150 g/s may hold ratio far better.
Reinforced systems add another layer. An RRIM machine handling glass or carbon fiber must account for fiber dispersion and short-fill risk, not raw flow alone. In those applications, the output calculation has to preserve mixing quality under abrasive and viscous conditions.
For structural or reinforced parts, output sizing must include fiber dispersion and short-fill avoidance more than raw flow. RRIM или RIM: какой процесс подходит для вашей конструкционной детали covers the process-selection trade-offs.

Заложите реалистичный запас производительности
After the calculation, add margin for conditions the rated spec does not include: hose length and pressure loss, day-tank conditioning, recirculation, mold indexing gaps, and stop-start behavior. These factors reduce the time the machine actually spends pouring.
A practical inquiry should specify these items together because each one shifts the required flow:
| Item to specify | Why it changes output | Example to send |
|---|---|---|
| Largest repeatable shot | Sets the minimum stable shot range | 175 g cavity, 4 cavities |
| Shortest station cycle | Sets peak demand | 18 с |
| Available pour time per cycle | Divides shot into flow | 4 s |
| Working viscosity at temperature | Affects pump and mixhead backpressure | 800–2500 mPa·s at 35 °C |
| Hose length and mixhead type | Adds pressure loss and wash volume | 30 m heated hose |
| Stop-start and recirculation | Consumes usable output outside pouring | 3–4 stops per shift |
Electrical safety and control reliability also need to be checked against the machine electrical standard [5], especially when the machine is integrated into an automated line with interlocked mold carriers and robot indexing.
Before you send the inquiry, reduce the problem to three numbers: largest repeatable shot in grams, shortest available pour time in seconds, and working viscosity at process temperature. Send those to info@chinahaifeng.com or WhatsApp 86 13566296633. That inquiry style tends to produce a flow-range and turndown recommendation, not a generic brochure quote.
Получите проверку подбора у инженера по полиуретановому оборудованию
Haifeng Polyurethane Machinery reviews output the way a production line actually consumes it: shot mass, pour window, demold time, recirculation, and wash cycle. Send your part or mold data, largest shot weight, shortest cycle, and whether you need low-pressure open pour or high-pressure shot repeatability.
Свяжитесь с нами: info@chinahaifeng.com или WhatsApp: 86 13566296633.
Вопросы и ответы: производительность пеногенераторной машины для полиуретана
Как обычно указывают производительность пеногенераторной машины?
It is usually stated as maximum flow in kg/min or g/s at a reference pressure. Useful sizing requires the flow available at your working pressure and viscosity, plus the repeatable low-flow limit.
Почему машина на 10 кг/мин кажется медленной на моей линии с короткими заливками?
Because maximum flow is not the limiting factor on a short-shot line. Cycle time, turndown, and metering accuracy dominate. If the pour window is only a few seconds per station, a lower nominal flow machine with better turndown can often outperform the larger unit.
Подбирать по максимальной производительности или по минимальной стабильной массе заливки?
Start from minimum stable shot weight, because that is where ratio error and mixing defects appear. Then verify that the same machine can cover the largest shot and the peak flow needed on the fastest cycle. Both conditions must hold on one machine.
Всегда ли высокое давление означает более высокую полезную производительность?
No. High pressure refers to impingement mixing energy and short-shot repeatability. It does not automatically increase daily production. On a long continuous pour, a well-matched low-pressure machine may be the more productive choice.
Какой запас следует добавить к расчётной производительности?
A common approach is to calculate the peak pour rate, then add 20–25% for stop-start, recirculation, hose pressure loss, and line pauses. The margin is a safeguard, not a substitute for verifying the machine can hold ratio at the low end.
Источники
[1] ASTM D1622-20, Стандартный метод определения кажущейся плотности жёстких ячеистых пластиков, ASTM International, West Conshohocken, PA, 2020.
[2] ISO 845:2006, Ячеистые пластмассы и резины — определение кажущейся плотности, Международная организация по стандартизации, Женева, 2006.
[3] G. Oertel, Polyurethane Handbook: Chemistry – Raw Materials – Processing – Application – Properties, 2nd ed., Hanser, Munich, 1994.
[4] D. Randall and S. Lee, The Polyurethanes Book, Wiley, Hoboken, NJ, 2002.
[5] EN 60204-1:2018, Safety of machinery — Electrical equipment of machines — Part 1: General requirements, CENELEC, Brussels, 2018.
Если вам интересно, ознакомьтесь с этими статьями по теме:
Как рассчитать массу впрыска в полиуретане
Причины усадки пенополиуретана и способы её контроля
Подберите дозирующий узел для непрерывного производства блочного поропласта
Slabstock production forms a continuously moving foam bun, which is cut and converted after foaming and conditioning. The buyer should give the proposed block cross-section, speed and density ranges by recipe, plus usable height and width after trimming. Ask how the dosing unit holds the A/B ratio during startup, stable production and recipe changes.
Evaluate accepted foam output with mass balance, density checks across the bun, usable dimensions and downstream handling capacity. Agree which material and time losses count as startup scrap and which samples are cut after conditioning. See Haifeng’s continuous slabstock foaming line, slabstock production solution и continuous slabstock project in Brazil.



