خلفية لافتة حل الشامواه المصنوع من الألياف الدقيقة الخالي من المذيبات

حل الشامواه الميكروفايبر الخالي من المذيبات

نسّق التشريب التفاعلي بالبولي يوريثان الخالي من المذيبات والكالندرة لركيزة الألياف الدقيقة المختارة.

تكوين العملية

متانة ميكانيكية فائقة للشامواه المصنوع من الألياف الدقيقة الفاخر لصناعة السيارات

يربط التشريب التفاعلي للألياف الدقيقة بين تحضير الركيزة وتكييف المكونات والخلط والتطبيق والتحكم في فجوة الالتقاء. ولا تُثبت قوة الكالندرة بحد ذاتها الاختراق الكامل أو تمنع وجود قلب جاف. وتنتمي مقاومة التمزق والرائحة إلى بنية الشامواه النهائية وظروف اختبارها.

نطاق توريد محدد

حدّد حزمة قياس الجرعات والتطبيق، والكالندرة، والمعالجة، والتشطيب. فالتركيبة الخالية من المذيبات لا تُثبت أن المادة عديمة الرائحة أو أن القبول التلقائي من مصنّعي المعدات الأصلية مضمون.

المدخلات لاختيار العملية

بيانات الألياف الدقيقة، والرطوبة، والراتنج، والالتقاط الرطب، وظروف فجوة الالتقاء/المعالجة، والملمس النهائي، ومتطلبات اختبار التمزق/الرائحة.

يُتفق على نطاق المعدات وواجهات المصنع المحتفظ بها والقبول للمادة والجزء المختارين. حدّد حزمة قياس الجرعات والتطبيق، والكالندرة، والمعالجة، والتشطيب. فالتركيبة الخالية من المذيبات لا تُثبت أن المادة عديمة الرائحة أو أن القبول التلقائي من مصنّعي المعدات الأصلية مضمون.

مسار الإنتاج

سير عمل الشامواه المصنوع من الألياف الدقيقة الخالي من المذيبات

حضّر الألياف الدقيقة ← حضّر البولي يوريثان وسلّمه ← شرّب وكلندر ← عالج وافحص. حدّد توقيت التحضير والتعبئة والمعالجة والإنتاج كلًا على حدة للتهيئة المختارة.

01

حضّر الألياف الدقيقة

تحقّق من النعومة والكتلة والرطوبة والبنية.

02

حضّر البولي يوريثان وسلّمه

تحقّق من التكييف والنسبة ونافذة التفاعل القابلة للاستخدام.

03

شرّب وكلندر

Establish application and nip conditions without damaging the substrate.

تكوين العملية

النطاق الهندسي للحل المرجعي

مراجع التكوين الحالي والاختبار. تُعد إعدادات المعدات ونتائج المواد ونتائج التجميع النهائي منفصلة؛ ويُطبَّق كل قيمة فقط على التكوين والظروف الموثقة الخاصة بها.

المعاملالقيمة / الوحدةالتكوين / الظروف المطبَّقة
Calendering Nip Clamping ForceUp to 150 kN (Hydraulic linear compression)Precision ground hardened steel rolls with thermal oil heating
Supported Microfiber FinenessDown to 0.05 DenierSea-island needle-punched nonwoven synthetic fleece
Finished Suede Tear StrengthGreater than or equal to 1.5x Natural LeatherISO 3377-2 testing (≥ 120 N vs 80 N genuine leather)
Automotive Interior Odor RatingVDA 270 Grade ≤ 2.5 (Tested at 65°C)100% solids solvent-free formulation with zero DMF
Continuous Line Working Speed3.0 to 15.0 m/minSynchronized roll-to-roll servo drive system
Working Web Width Envelope1,400 to 1,600 mmDual-die slotted manifold on heavy-duty machine bed
Existing application note: The 150 kN reference is total roll or nip force. Material penetration, tear resistance and odor depend on the selected material system and test conditions. Emissions and exposure are assessed for the complete process. Original process references, with their existing values: Moisture < 0.2%; Substrate fleece 0.05D (200–600 g/m²); confirm for selected material and tooling; Tank vacuum ≤ 0.05 kPa; Dosing accuracy ±0.2%; confirm for selected material and tooling; Working pressure 0.5–0.8 MPa; Output 1.0–12.0 kg/min; confirm for selected material and tooling; Calendering force up to 150 kN; Roll temp 80–100°C; confirm for selected material and tooling; Drum temp 120°C ± 1°C; Tear strength ≥ 1.5x leather; confirm for selected material and tooling. The original microfiber example has 350 g/m² basis mass. Confirm the substrate and wet pickup for the intended construction. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.

المعدات الأساسية لهذا الحل

تُختار مراجع المعدات وفق عمليتها الموثّقة. القياس الرئيسي للجرعات والإمداد المساعد والمسارات البديلة ليست حزمة قياسية واحدة.

ضوابط العملية وفحوص التطبيق

قيّم هذه الوظائف باستخدام المادة والتجهيزات القالبية الموجزة الإنتاجية المختارة. تتطلب نتائج الأجزاء النهائية أدلة قبول خاصة بها.

Substrate-matched impregnation

Develop resin delivery and nip conditions for the actual fiber network.

Defined uniformity checks

Inspect core and cross-web distribution rather than assuming full penetration.

Comparable material tests

Use stated specimens and conditioning for tear and odor comparisons.

مشاريع ذات صلة

هذه مراجع تطبيقية ذات صلة. قارن المادة الفعلية والعملية والوحدات المسلّمة؛ فأرقام المشاريع المبلَّغ عنها ليست نتائج قبول لخط آخر.

مراجعة المشروع
أسئلة التخطيط

الأسئلة الشائعة حول تخطيط الإنتاج

الاختيار ونطاق التوريد والتحقق لهذا المسار الإنتاجي.

Does nip force establish full impregnation? +
No. Viscosity, reaction time, substrate and application arrangement also matter. Verify representative cross-sections and width positions.
Does solvent-free processing guarantee OEM odor approval? +
No. The full material and manufacturing history must meet the specified finished-product test.
ما المعلومات المطلوبة لإعداد تكوين أولي؟ +
Microfiber data, moisture, resin, wet pickup, nip/cure conditions, final hand and tear/odor test requirements. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

ناقش أهدافك الإنتاجية

Share the following with your production brief: Microfiber data, moisture, resin, wet pickup, nip/cure conditions, final hand and tear/odor test requirements. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

اتصل بنا

لمعرفة كيفية تعاملنا مع معلومات استفسارك، اقرأ سياسة الخصوصية.

مراجعة التكوين بناءً على بيانات التطبيق والمواد وثائق المعدات والواجهات والقبول المتفق عليها تدريب ودعم محدَّدان للحزمة المورَّدة
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube