Automotive SMC Sheet and Compression Molding Solution Banner background

حل إنتاج صفائح SMC والقولبة بالضغط للسيارات

Plan heated compression molding of prepared SMC charges with defined tooling and handling interfaces.

Traditional Sheet Molding Compound (SMC) compression molding for automotive structural and exterior parts

حل إنتاج صفائح SMC والقولبة بالضغط للسيارات

For the route described here, a prepared sheet-molding-compound charge is placed in a heated matched mold, compressed, cured and removed. Charge placement, press movement and thermal conditions follow the selected SMC and part. Upstream sheet manufacture and liquid-resin impregnation are separate operations.

نطاق توريد محدد

Confirm whether the supply is a compression cell or also includes upstream material preparation. Do not treat an associated liquid-PU metering project as proof of the same prepared-sheet process without its process records.

المدخلات لاختيار العملية

SMC data, charge drawing, part CAD, mold envelope and mass, required force/thermal cycle, output and upstream supply boundary.

Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Confirm whether the supply is a compression cell or also includes upstream material preparation. Do not treat an associated liquid-PU metering project as proof of the same prepared-sheet process without its process records.

مسار الإنتاج

Automotive SMC Sheet and Compression Molding Workflow

Define the SMC charge → Load the heated tool → Compress and cure → Demold and inspect. Define preparation, filling, cure and output timing separately for the selected configuration.

01

Define the SMC charge

Confirm sheet material, charge pattern, storage and handling.

02

Load the heated tool

Position the charge and any inserts in the selected mold.

03

Compress and cure

Coordinate press motion and thermal control with the material instructions.

الإعداد & معايير العملية

Material, process and acceptance data

مراجع التكوين الحالي والاختبار. تُعد إعدادات المعدات ونتائج المواد ونتائج التجميع النهائي منفصلة؛ ويُطبَّق كل قيمة فقط على التكوين والظروف الموثقة الخاصة بها.

Material definitionSMC is a pre-compounded, fiber-reinforced resin sheet; its resin chemistry is selected for the application and is not inherently polyurethane.
ProcessCut sheet charges are placed in a matched heated mold and compression molded; charge coverage and placement affect material flow and part quality.
Equipment planningPress force, platen size, tool heating, sheet loading, demolding and trim interfaces are selected from the part envelope, material and production target.
LFI distinctionLFI cuts glass-fiber roving in line, wets it with PU and deposits it into an open mold. It should not be labelled conventional SMC sheet molding.
Haifeng solution scopeEngineering scope: SMC sheet and charge-layout planning, heated matched-mold press integration, part take-out, trimming and inspection; equipment scope follows the confirmed project requirements.
Existing application note: Values on this solution page must be confirmed for the selected material, product, test method and operating conditions in the project proposal. Existing project records are specific to their own configurations. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.
معدات قياس الجرعات والخلط والخطوط

معدات Haifeng ذات الصلة

تُختار مراجع المعدات وفق عمليتها الموثّقة. القياس الرئيسي للجرعات والإمداد المساعد والمسارات البديلة ليست حزمة قياسية واحدة.

اعتبارات هندسية

ضوابط العملية وفحوص التطبيق

قيّم هذه الوظائف باستخدام المادة والتجهيزات القالبية الموجزة الإنتاجية المختارة. تتطلب نتائج الأجزاء النهائية أدلة قبول خاصة بها.

Clear material entry point

Prepared SMC charge molding is distinguished from resin injection and chopped-fiber deposition.

Press and tool coordination

Select usable force, platen envelope and thermal controls for the part and tool.

Evidence matched to the route

Use project records only after confirming resin, reinforcement introduction and actual delivery scope.

أسئلة تخطيط الإنتاج

Automotive process FAQs

Process, material selection and validation for Traditional Sheet Molding Compound (SMC) compression molding for automotive structural and exterior parts.

Does this page include SMC sheet manufacture? +
Only if the upstream preparation and sheet-making equipment are explicitly listed in the agreed scope. A compression press alone does not supply that process.
Can RIM or LFI results be used as SMC performance evidence? +
Not automatically. Reinforcement introduction, resin flow and consolidation differ. Verify the actual material and process in each project.
ما المعلومات المطلوبة لإعداد تكوين أولي؟ +
SMC data, charge drawing, part CAD, mold envelope and mass, required force/thermal cycle, output and upstream supply boundary. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

أرسل أهداف إنتاجك

Share the following with your production brief: SMC data, charge drawing, part CAD, mold envelope and mass, required force/thermal cycle, output and upstream supply boundary. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

اتصل بنا

لمعرفة كيفية تعاملنا مع معلومات استفسارك، اقرأ سياسة الخصوصية.

مراجعة التكوين بناءً على بيانات التطبيق والمواد وثائق المعدات والواجهات والقبول المتفق عليها تدريب ودعم محدَّدان للحزمة المورَّدة
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube