دراسات حالة المشاريع

مشروع رغوة VIP والبولي يوريثان للمجمدات الطبية في الصين

موجز مراجعة مشروع رغوة المجمدات فائقة الانخفاض في الحرارة المدمجة بتقنية VIP. تكوين المعدات ونطاق التنفيذ والنتائج المبلّغ عنها.

نظرة عامة على المشروع

تنبيه بشأن الرسم التوضيحي. الرسوم التوضيحية للعملية ليست صورًا فوتوغرافية موثّقة لهذا التجهيز.

أساس مرجعية المشروع. الأرقام وتفاصيل التكوين مُبلَّغ عنها في موجز المشروع المقدَّم. وهي قيم مرجعية للتطبيق المذكور، وليست نتائج قبول موثّقة ولا ضمانًا لتجهيز آخر. يجب التحقق من السجلات المصدرية والمواد والتجهيزات القالبية وجدول التشغيل وطريقة الاختبار عند تقييم مشروع مماثل.

حالة أدلة المشروع. تصف الوثيقة المقدَّمة هذا التكوين وتورد النتائج أدناه. سجلات القبول الأصلية وتقارير الاختبار والوسائط غير مرفقة بهذه الاستيراد؛ ويتطلب الإسناد والنتائج التحقق قبل استخدامها كدليل شراء.

يصف الموجز المقدَّم سياق المشروع التالي.

A leading national cryogenic medical equipment technology enterprise in Anhui deployed Haifeng’s specialized VIP composite polyurethane foaming system. The project was commissioned to manufacture high-reliability insulation envelopes for 500 L to 800 L ultra-low temperature (-86°C) biological vaccine and specimen freezers.

Prior to this deployment, the manufacturer faced severe yield losses. High-velocity chemical streams from legacy mixing heads physically shifted and punctured fragile barrier foils on pre-installed vacuum insulation panels (VIP), causing a 6.5% panel failure rate. Furthermore, poor interfacial foam-to-VIP wet-out created micro-air chimneys; during power failure simulations, cabinet temperatures rose from -86°C past the stated -60°C test endpoint in just 1.5 hours, not meeting the submitted design target; biological storage requirements require separate validation.

Haifeng supplied an integrated micro-momentum foaming cell centered on the HF-ULT86-VIP system. Featuring diffused multi-port dispensing (< 8 m/s) and soft-vacuum cavity drawing (85 kPa), the equipment aimed to reduce VIP puncture defects, raising total wall thermal resistance by 40% and extending off-grid cold holding time to 4.2 hours.

قيود البيانات: Do not turn a -60°C trial endpoint into a universal vaccine/specimen safety threshold. The 0-defect claim is a submitted finite sample, not a guarantee. Cavity 85 kPa absolute and VIP internal vacuum are separate.

تنفيذ الحلول

تكوين المعدات المُبلَّغ عنه من الموجز المقدَّم:

Haifeng engineered an ultra-gentle, high-pressure encapsulation cell designed for fragile composite assemblies. Pre-tested VIP panels are mounted into dedicated positioning grooves on the stainless steel cabinet liner using non-penetrating magnetic holders.

The cabinet core is positioned in a precision hydraulic clamping fixture, where a soft-vacuum skid evacuates the mold cavity to 85 kPa. High-functionality polyol and polymeric isocyanates are metered at 15.0 MPa via servo axial piston pumps under continuous Coriolis mass flow measurement.

Material discharges through a low-momentum multi-port diffuser head. Stream velocity is slowed from 30 m/s to 8 m/s, spreading gently into narrow 25 mm gaps behind the VIP panels without tearing the barrier films. Driven by soft-vacuum expansion, the fine closed-cell polyurethane foam locks tightly against the VIP surfaces, eliminating interfacial voids. After 15 minutes of in-mold curing at 45°C, the insulated cabinet undergoes 100% infrared thermal imaging to verify zero cold-bridge leakage.

Do not turn a -60°C trial endpoint into a universal vaccine/specimen safety threshold. The 0-defect claim is a submitted finite sample, not a guarantee. Cavity 85 kPa absolute and VIP internal vacuum are separate.

المعداتالطرازالكميةالوظيفة
Medical Freezer VIP Foaming SkidHF-ULT86-VIPمجموعة واحدةCore 15 MPa low-momentum metering, fluid heating, and soft-vacuum dispensing.
Low-Momentum Multi-Port Diffuser HeadHF-LMD-01وحدة واحدةStream velocity diffuser (< 8 m/s) preventing VIP barrier foil puncture.
Soft-Vacuum Mold Evacuation SkidHF-SVS-85وحدة واحدةMaintains 85 kPa cavity pressure to facilitate gentle low-void foam flow.
Precision Hydraulic Clamping FixtureHF-HCF-800مجموعة واحدةClamps 800 L medical cabinet with integrated water temperature channels.

النتائج المبلّغ عنها — السجلات قيد التحقق

4.2 Hours
Off-Grid Cold Holding Time
The brief reports 4.25 h to a -60°C center-point endpoint after power-off from -86°C at 25°C ambient. Cabinet loading, sensor locations and original test records are required; biological storage limits are separate.
0
VIP Panel Puncture Defects
The brief reports no punctures in a 1,000-cabinet production series. Its described sample inspection does not establish every panel’s vacuum integrity; sampling and records require review.
40%
Total Thermal Resistance Gain
Reported wall resistance gain 41.2% versus a non-VIP reference at a 100 mm wall section. The steady-state measurement, specimen boundaries and thermal-bridge contribution require verification.

Upgrade Your Cryogenic Medical Freezer Insulation

شاركنا تطبيقك ونظام المواد لديك والطاقة الإنتاجية المستهدفة وظروف المصنع. سيرد فريقنا خلال يوم عمل واحد. وبمجرد أن تتضح المتطلبات، نقدّم عرضًا أوليًا خلال يومَي عمل.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube