Special-Structure and Retrofit PU Foaming Solution Banner background

Решение для ППУ-вспенивания специальных конструкций и при реконструкции

Подбор оборудования для ППУ-напыления на криволинейные конструкции и при выборочной реконструкции кровли с оценкой основания, доступом, подготовкой материала и защитными покрытиями, подобранными под проект.

Curved / Roof Application geometry reviewed through trials
2–3s Supplied cream-time reference; not full cure
40–48кг/м³ Справочная плотность поставляемой рецептуры
Adaptive Architecture & Facility Modernization

Adaptive In-Situ Polyurethane Solutions for Irregular Structures & Building Retrofits

Fast-reacting formulations can support spraying on curved and overhead surfaces within a validated application window. Cream time, cure, recoat timing and pass thickness follow the selected material data and trials. Retrofit feasibility depends on structural condition, moisture, fastener repairs, access and work-area controls.

Curved and Overhead Application

Review access, spray distance, pass thickness and material reaction stages through representative trials. Cream time marks the start of foam rise and is not full cure.

Retrofit and Warranty Scope

Assess the roof structure, corrosion, moisture and fixing repairs before application. Coating service life and any roofing warranty are defined separately by the responsible system supplier or contractor.

Start either with a curved/overhead application trial or with a condition survey of the existing roof. Retrofit repair, substrate moisture, fasteners and work access remain separate from foam spraying; fast cream time is not full cure or structural repair.

Производственный процесс

Production Workflow for Special Structure & Retrofit PU Foaming Line

Последовательность настраивается под выбранное применение и материал. Температуры, давления, время реакции и толщина за проход являются справочными условиями, проверяемыми в ходе испытаний проекта.

01

Rust Neutralization & Substrate Surface Priming

Assess roof condition and repair structural or fixing defects before application. Clean and prepare the substrate; verify moisture and adhesion for the selected material.

CLEANLINESS: OIL/DUST-FREE | MOISTURE: LESS THAN 8% | PULL-OFF: GREATER THAN 0.25 MPA
02

High-Pressure Precursor Thermal Stabilization

Condition the formulation through the selected proportioner and heated hose. Set temperature, mix ratio and delivery duty against material data and equipment limits.

FLUID TEMP: 52°C–58°C | MIX RATIO: SELECTED FORMULATION; COMPONENT CALIBRATION REQUIRED | HOSE REACH: UP TO 90 M
03

Multi-Pass In-Situ Anti-Sag Foam Spraying

Apply the selected fast-reacting formulation within validated pass-thickness and cooling limits. Cream time starts foam rise; cure and recoat timing are separate stages.

PRESSURE: 150–180 BAR REFERENCE | CREAM TIME: 2–3 S REFERENCE | SURFACE SUITABILITY: VALIDATED THROUGH TRIALS
Конфигурация и технологические параметры

Технические характеристики

Предоставлены прикладные и оборудованные ориентиры для рассмотрения конфигурации. Свойства материала, условия эксплуатации и приёмочные испытания согласуются для выбранного проекта.

Технический параметрПредоставленный ориентир / конфигурацияИнженерный контекст и проверка
Целевое применениеParametric 3D Domes, Aging Industrial Roof RetrofitsIrregular geometry and non-destructive renovation
Матрица материаловЖёсткий полиуретан (PUR) / полиизоцианурат (PIR)Fast-cream anti-sag formulation
Operating Incline AnglesHorizontal, vertical and overhead surfacesFormulation, pass thickness and substrate conditions validated through trials
Плотность сердечника из пены40 – 48 кг/м³Supplied material-density reference; structural repairs and design assessed separately
Теплопроводность (λ)0.020–0.022 (supplied reference) W/(m·K)Метод теплотехнических испытаний, средняя температура, кондиционирование и старение подлежат согласованию
Прочность на отрыв при растяжении>0.25 MPa (To aged steel / concrete)Испытание адгезии методом отрыва
Производительность пропорционера по жидкости6 – 14 кг/минControlled spray pattern for detailed geometry
Давление на выходе оборудования отличается от давления расширения в закрытой полости. Для выбранной модели проверяются давление, расход, температура и нагрузка на шланги. Для теплотехнических характеристик требуются указанные материал и условия испытаний.
Инженерные аспекты

Ключевые инженерные преимущества

Управление процессами, оснастка и интеграция оборудования с учётом конкретных задач применения.

Geometry-Specific Trials

Validate spray behavior, adhesion and thickness on the intended surfaces.

Roof-Condition Review

Assess structure, moisture, corrosion and fixing repairs before selecting a retrofit route.

Material Reaction Control

Separate cream time, tack-free time, cure and recoat timing in the application plan.

Defined Protective Finish

Select coating compatibility, maintenance and warranty scope for the roofing system.

Вопросы планирования производства

Часто задаваемые вопросы

Сравните производственные маршруты, требования к материалам, конфигурации оборудования и исходные данные проекта.

Can foam be sprayed onto overhead surfaces? +
Select a suitable formulation and validate pass thickness, reaction behavior, substrate condition and adhesion through trials. A short cream time alone does not establish overhead performance.
Can factory operations continue during roof work? +
Agree access, isolation, ventilation, overspray controls and work-area arrangements with the site. Operational continuity depends on the construction plan and site conditions.
Can SPF repair loose fasteners or structural roof defects? +
Repair fixings, corrosion and structural defects before application as required by the roof assessment. Foam coating does not replace necessary mechanical or structural repairs.
Does a 2–3 s cream time mean the foam is fully cured? +
Cream time is the start of visible foam rise. Tack-free time, full cure and recoat timing are separate material-dependent stages.
What defines service life and commissioning time? +
The protective finish, application, exposure and maintenance determine roofing-system service life. The supplied equipment-commissioning reference is 12–15 days; final scope and timing are agreed for the project.
Какие исходные данные нужны для этой конфигурации? +
Geometry and height, substrate survey, moisture/defects, structural repair needs, material system, protective layer and work-zone plan. Identify retained equipment and the required acceptance documents.
Can roof retrofit feasibility be decided from spray speed? +
No. Assess structure, corrosion, moisture, loose fixings, access and operational constraints first. Trial adhesion and thickness on the intended surfaces, then agree protection, cure and inspection.

Обсудите ваше оборудование для изоляции и его применение

Share the following for this application: Geometry and height, substrate survey, moisture/defects, structural repair needs, material system, protective layer and work-zone plan. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Связаться с нами

О том, как мы обрабатываем информацию из вашего запроса, читайте в Политика конфиденциальности.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube