Autoclave Composite Molding Production Solution Banner background
Производственные решения

Производственное решение для формования композитов в автоклаве

Coordinate prepreg layup, vacuum bagging and a qualified autoclave pressure/temperature cycle.

Цель производства

Стройте процесс вокруг своего изделия

Coordinate prepreg layup, vacuum bagging and a qualified autoclave pressure/temperature cycle.

Сначала изделие и материал

Начните с чертежа готового изделия, системы материалов и требований к приемке. Технологический маршрут и комплектация оборудования оцениваются совместно.

Производительность по всему процессу

Определяйте выпуск с учетом подготовки, формования/реакции, отверждения, обработки и контроля. Практическую производительность линии определяют самый медленный этап и смены изделий.

Состав оборудования и процесса

Specified vessel/door, heating/circulation, pressurization, vacuum circuits and controls. Tooling, prepreg, gas supply, facility design and applicable pressure-vessel documentation are separately agreed.

Валидация и планирование производства

The 3.5 m × 12 m clear working envelope and approximately 130 m³ total vessel volume describe different geometry. Ultrasonic inspection coverage and quantitative laminate porosity are separate acceptance tasks. Equipment capability does not by itself establish aerospace qualification.

Define usable loaded space, tool mass, vacuum channels and part-temperature monitoring alongside the autoclave cycle. Vessel design/operating limits, thermal uniformity and aerospace component qualification are different requirements with separate records.

Производственный процесс

От подготовки до годного изделия

Последовательность планирования для указанного маршрута. Окончательные настройки и условия приемки устанавливаются по результатам анализа материала и детали.

01

Define the laminate

Review prepreg, tool, part dimensions and required qualification.

02

Control storage and layup

Track material exposure, ply orientation and intermediate compaction.

03

Bag and instrument

Arrange seals, vacuum connections and part/tool temperature monitoring.

Исходные данные для проектирования

Информация, необходимая для настройки линии

Предоставьте эти данные, чтобы можно было определить состав оборудования, интерфейсы и план валидации.

Проектные данныеТребуемая информация
Part envelopeTool/part dimensions, mass and laminate thickness
PrepregStorage/out-time and approved cure instructions
Autoclave interfaceVessel capacity, pressure, thermal and vacuum requirements
ПриёмкаCure records, dimensional and laminate tests

Large Aerospace Composite Application: Configuration Reference

The following supplied configuration illustrates a large-tool curing package. Final pressure-vessel requirements, facility services, approved material cycles and part qualification are agreed separately.

ПараметрЗначение / единица измеренияПрименимая конфигурация / условия
Effective Working DimensionsØ 3,500 mm Diameter x 12,000 mm LengthAccommodates 11m monolithic wingbox panels and spars; configuration-specific reference or part acceptance target
Maximum Vessel Operating Pressure0.1 to 1.5 MPa (15 bar)High-purity dry nitrogen gas pressurization; configuration-specific reference or part acceptance target
Operating Temperature RangeAmbient up to 250°CMulti-zone electric finned circulation heaters; configuration-specific reference or part acceptance target
Thermal Field UniformityWithin ±1.5°C across working zone24-point temperature survey using the agreed method and load conditions; configuration-specific reference or part acceptance target
Ultrasonic Inspection Pass RatePart acceptance target defined in the technical agreementUltrasonic coverage, acceptance criteria and quantitative porosity measurement are separate; use the agreed part-specific method and acceptance criteria
Cured Laminate Porosity LevelPart acceptance target defined in the technical agreementUltrasonic coverage, acceptance criteria and quantitative porosity measurement are separate; use the agreed part-specific method and acceptance criteria

Vacuum, Cure Records and Laminate Acceptance

The supplied package includes 48 independent tooling-vacuum channels, bag-leak monitoring, zoned heating, circulation, gas pressurization and controlled cooling. Its process reference uses nitrogen purity of at least 99.9%, a bag-vacuum reference of 0.05 kPa absolute and a leak-rate reference below 0.05 kPa/min. Conditions and measurement boundaries are specified for each tool and bag.

An example cure schedule ramps at 1.5°C/min to 180°C, holds at 1.5 MPa for 120 minutes and cools at 1.8°C/min. The available ramp-rate reference is 0.5–2.5°C/min. Vacuum-line venting follows the approved material procedure; this example is not a universal prepreg cure recipe.

The supplied below-0.2% laminate porosity target and ultrasonic inspection coverage require separate methods and acceptance criteria. An 85 kg fastener comparison applies only to its specified aircraft structure. Equipment capability and a large working envelope do not establish aerospace qualification.

This table is a design brief, not a machine performance guarantee. Rated values are confirmed in the project proposal with their material and operating conditions. The 3.5 m × 12 m clear working envelope and approximately 130 m³ total vessel volume describe different geometry. Ultrasonic inspection coverage and quantitative laminate porosity are separate acceptance tasks. Equipment capability does not by itself establish aerospace qualification.
Проектирование

Согласуйте оборудование с процессом

Оцените повторяемость, обращение с деталями и приёмку на всех этапах рабочего процесса.

Autoclave Cycle Control

Coordinate vessel pressure, vacuum channels, thermal uniformity and part-temperature records for the qualified cure schedule.

Cycle measurements

Record vessel pressure, vacuum channels and actual part temperatures.

Separate qualifications

Keep vessel suitability and finished-laminate evidence as distinct acceptance items.

Independent vacuum monitoring

Configured vacuum channels retain tool-bag vacuum and leak-alarm records alongside the approved cure schedule.

Подтверждение применения

Связанные проекты

The wingbox record is an application reference. Confirm actual supplied modules and qualification documents rather than inferring aviation approval from vessel ratings.

Просмотреть запись
Вопросы планирования

Часто задаваемые вопросы

Опре­делите производственный маршрут до выбора машины.

What does thermal-pressure molding mean here? +
The term refers to autoclave molding with controlled heat and vessel pressure, together with the specified vacuum-bag arrangement.
Какая информация нужна для определения размеров производственной линии? +
Tool/part envelope and mass, batch loading, prepreg cycle, vacuum channels, thermocouples, site services and inspection. Identify retained equipment, the working schedule and required acceptance documents.
Что входит в комплект оборудования? +
The autoclave is one core module; loading, vacuum, tooling, utilities and inspection need a defined delivery boundary. Define usable loaded space, tool mass, vacuum channels and part-temperature monitoring alongside the autoclave cycle. Vessel design/operating limits, thermal uniformity and aerospace component qualification are different requirements with separate records.
Фиксированы ли время цикла и характеристики готовой продукции? +
Они устанавливаются для выбранного материала, геометрии, оснастки и приёмочных испытаний. В предложении указываются целевые условия и проверка, необходимая до окончательного обязательства по характеристикам.
What should be verified under the actual autoclave load? +
Confirm usable clearances, circulation, vacuum connections and part-temperature histories for the intended tools. Keep vessel documents, loaded thermal checks and laminate acceptance separate.

Опишите свои производственные задачи

Share the following for this application: Tool/part envelope and mass, batch loading, prepreg cycle, vacuum channels, thermocouples, site services and inspection. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Связаться с нами

О том, как мы обрабатываем информацию из вашего запроса, читайте в Политика конфиденциальности.

Анализ продукта и материала Обсуждение процесса и объёма работ
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube