Проект совместного нанесения покрытия на магистральный газопровод в Китае

Реализованный проект

Обзор проекта

Примечание об иллюстрации. Иллюстрации процесса не являются проверенными фотографиями данной установки.

Основание проекта как референса. Цифры и сведения о конфигурации приведены в предоставленном описании проекта. Это справочные значения для указанного применения, а не подтверждённые результаты приёмки или гарантия для другой установки. При оценке аналогичного проекта проверяйте исходные записи, материал, оснастку, режим работы и метод испытаний.

A state-owned natural gas transmission enterprise in Northern China deployed Haifeng’s mobile automated hydraulic polyurea spraying units for the external corrosion protection of a major 1,219 mm diameter cross-country gas pipeline. The project covered critical horizontal directional drilling (HDD) crossings through wetlands and saline-alkali terrain spanning 18 kilometers.

Field application occurred in challenging sub-zero winter conditions with ambient temperatures plummeting to -15°C. Traditional pneumatic spray setups and heat-shrink sleeves previously deployed suffered from thermal dissipation along long lines, creating viscosity imbalances that produced microscopic pinholes and poor interfacial adhesion. These flaws caused widespread failures during mandatory 15 kV high-voltage electrical holiday testing.

Haifeng engineered an all-weather mobile hydraulic spraying package centered on the HF-PIPE1400-HYD. Equipped with 120-meter copper-mesh heated hoses and automated pipe-joint rotary indexing units, the system delivered non-pulsing 21 MPa impingement spraying under strict thermal control, achieving continuous, holiday-free barrier membranes across the entire 18-kilometer crossing section.

Реализация решений

Haifeng engineered and deployed a high-mobility, cold-weather field spraying package integrated into all-terrain track vehicles. The steel pipeline joints (OD 1,219 mm) were abrasive-blasted to Sa 2.5 cleanliness and preheated to 55°C using an automated medium-frequency induction induction band.

Chemical streams—amine-terminated polyether curative and polymeric MDI—were pumped from heated 200 L drums into the HF-PIPE1400-HYD hydraulic proportioner. Coaxial double-acting hydraulic cylinders maintained stable fluid delivery at 19.5 MPa, eliminating pressure drops during pump stroke reversals.

The chemical lines were routed through 120 meters of copper-jacketed heated umbilical cables to keep fluid temperatures at 65°C right at the pipe face despite sub-zero outdoor weather. Technicians operated automated circular orbital carriages carrying mechanical-purge impingement spray guns. The carriage executed synchronized rotational passes around each welded girth joint, building a uniform 1.8 mm pure polyurea coating in under 8 minutes per joint without drips or sagging.

ОборудованиеМодельКол-воФункция
Automated Pipeline Polyurea ProportionerHF-PIPE1400-HYD2 комплектаCore hydraulic proportioning, fluid heating to 19.5 MPa and 65°C.
120-Meter Heated Umbilical CableHF-HUC-120M2 комплектаCopper-mesh wrapped thermal lines maintaining 65°C at -15°C ambient.
Automated Girth Joint Spraying CarriageHF-ORC-12002 шт.Orbital motorized ring driving spray guns smoothly around 1,219 mm pipes.
High-Voltage Holiday Detector RingHF-HVD-15K2 шт.Automated 15 kV rolling spring electrode verifying zero pinhole defects.

Заявленные результаты проекта — ожидается подтверждение документами

0
Reported Field-Joint Holiday Inspection Result
Reported in the supplied project brief: no detected holidays on 1,500 field joints associated with an 18 km section using a stated 15 kV procedure. Coverage, thickness, voltage selection and original inspection logs require verification; this is not proof of dielectric breakdown strength.
≤ 4.2 mm
Радиус катодного отслаивания
Reported in the supplied project brief: 4.15 mm disbondment on site specimens after 48 hours at 65°C and a stated -1.5 V potential. The referenced ASTM G8/ISO 21809-3 procedure and acceptance basis require original report checks; no universal compliance claim is made.
8 min
Joint Coating Cycle Time
Reported in the supplied project brief: eight minutes from spray start to the stated film-setting endpoint on a Ø1,219 mm joint at 1.8 mm dry film. This excludes unconfirmed preparation and full-cure stages.

Protect Your Pipeline Infrastructure from Corrosion

Расскажите о вашей задаче, системе материалов, целевом объёме выпуска и условиях на производстве. Наша команда ответит в течение одного рабочего дня. После уточнения требований мы в течение двух рабочих дней предоставим предварительное предложение.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube