Casos prácticos de proyectos

Proyecto de línea de encapsulado de estator largo para maglev en China

Project review brief for vacuum potting for maglev stator components. Equipment configuration, implementation scope and reported outcomes.

Resumen del proyecto

Aviso sobre las ilustraciones. Las ilustraciones del proceso no son fotografías verificadas de esta instalación.

Base de la referencia del proyecto. Las cifras y los detalles de configuración se reportan en el resumen del proyecto suministrado. Son valores de referencia para la aplicación indicada, y no resultados de aceptación verificados ni una garantía para otra instalación. Confirme los registros de origen, el material, el utillaje, el programa de operación y el método de ensayo al evaluar un proyecto comparable.

Estado de la evidencia del proyecto. El documento proporcionado describe esta configuración y presenta los resultados que se indican a continuación. Los registros de aceptación originales, los informes de pruebas y los archivos multimedia no se adjuntan a esta importación; la atribución y los resultados requieren verificación antes de utilizarse como evidencia para una compra.

El resumen proporcionado describe el siguiente contexto del proyecto.

A national commercial high-speed maglev operation and maintenance center in Shanghai deployed Haifeng’s three-component vacuum casting system to upgrade its long-stator linear synchronous motor overhaul and refurbishment facility. The installation was commissioned to rebuild stator packs intended for a long-stator refurbishment application; commercial operating speed is not established by this brief.

Previously, the maintenance center utilized legacy epoxy potting formulations. The low thermal conductivity of epoxy (0.22 W/(m·K)) caused stator core temperatures to exceed 115°C under maximum acceleration, triggering localized micro-cracks and partial discharge (PD) electrical flashovers. Furthermore, manual paddle-mixing of abrasive alumina filler powders introduced air pockets, causing an 18.5% component rejection rate and requiring over 4 hours per stator section.

Haifeng engineered an automated liquid encapsulation cell centered on the HF-MGV150-3K platform. Featuring in-line vacuum high-shear powder dispersion and deep 0.05 kPa vacuum chamber potting, the upgraded facility achieved low-void encapsulation with thermal conductivities reaching 1.15 W/(m·K) and dielectric breakdown strengths exceeding 22 kV/mm, drastically lowering operational motor temperatures.

Limitaciones de los datos: The brief varies between a 38–40 minute potting cycle and a two-hour cure. Do not call the short cycle a completed cure/demold cycle. Destructive dielectric-breakdown testing and non-destructive partial-discharge testing are different measurements. Commercial operation at 600 km/h is not established by this brief.

Entrega de soluciones

Configuración del equipo reportada en el resumen proporcionado:

Haifeng engineered an ultra-clean, heavy-duty three-component potting cell tailored for abrasive, high-filler polyurethane formulations. Micro-scale aluminum oxide (Al₂O₃) powders are vacuum-dried and inducted directly into polyol streams inside an oil-jacketed 150 L vessel, where high-shear dispersers achieve 50% powder loading under 0.05 kPa vacuum.

Components—filled polyol, aliphatic isocyanate, and liquid catalyst—are metered via tungsten-carbide-lined gear pumps monitored by Coriolis mass flow meters, holding stoichiometric accuracy within ±0.3%. Fluid lines are maintained at 65°C to stabilize viscosities.

The 3-meter-long maglev stator core is loaded into a sealed vacuum chamber and evacuated to 0.05 kPa. The wear-resistant dynamic mixing head traverses along the stator slots, dispensing 12 kg of reactive formulation within 50 seconds. The fluid self-levels deeply into narrow copper winding clearances without trapped air. The encapsulated core cures isothermally at 80°C in an integrated curing tunnel, followed by 100% partial discharge testing to confirm the specified electrical acceptance criteria.

The brief varies between a 38–40 minute potting cycle and a two-hour cure. Do not call the short cycle a completed cure/demold cycle. Destructive dielectric-breakdown testing and non-destructive partial-discharge testing are different measurements. Commercial operation at 600 km/h is not established by this brief.

EquiposModeloCant.Función
Three-Component High-Thermal CasterHF-MGV150-3K1 unidadCore powder dispersion, 0.05 kPa degassing, and wear-resistant servo metering.
3-Meter Long-Stator Vacuum Potting ChamberHF-VPC-301 unidadHermetic vacuum enclosure accommodating 3m stator packs down to 0.05 kPa.
Alumina Powder Vacuum Induction SkidHF-AVI-011 unidadDust-free vacuum charging and de-agglomeration of micro-scale alumina powder.
Stator Preheating & Isothermal Cure TunnelHF-PCT-801 unidadThermal convection tunnel maintaining 70°C preheat and 80°C post-cure cycles.

Resultados declarados — Registros pendientes de verificación

≥ 22 kV/mm
Reported Material Dielectric Breakdown Strength
The brief reports 22.5 kV/mm from an insulation-material breakdown method. Specimen thickness, electrodes, conditioning and original records require verification. This is distinct from a 100% stator partial-discharge inspection.
1.15 W/(m·K)
Conductividad térmica del núcleo
Reported material conductivity 1.15 W/(m·K) for an alumina-filled formulation, referencing ISO 22007-2. Filler fraction, sample and original report require review; motor temperature is a separate result.
40 min
Reported Evacuation and Potting Time
The brief reports 38 minutes for evacuation and potting, while the solution specifies two hours at 80°C for curing. Complete cure/demold and total throughput require reconciliation.

Upgrade Your Maglev Motor Insulation & Thermal Dissipation

Comparta su aplicación, sistema de materiales, producción objetivo y condiciones de la fábrica. Nuestro equipo le responderá en un día hábil. Una vez aclarados los requisitos, le proporcionamos una propuesta preliminar en un plazo de dos días hábiles.

Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube