Dual-Density Car Seat Foaming Line Solution Banner background

Dual-Density Car Seat Foaming Line Solution

Define dual-density seat feed circuits, mixing-head routing and the zone interface before line selection.

Complete Turnkey Solution for Dual-Density Seat Foaming

Dual-Density Car Seat Foaming Line Solution

Dual-density seat production requires defined material recipes, regions and their bonding/transition. The stated primary material circuits and the mixing-head passages or chambers describe different parts of the system. Do not infer an additional material feed solely from a head label, or treat a ratio/index change as an unrestricted density-control method.

Alcance de suministro definido

Confirm the feed/return schematic, head model, active mixing sequence, robot and turntable. Single-shot versus sequential zone filling and mixed-model operation require representative material and mold trials.

Insumos para la selección del proceso

Seat zone map, recipes, feed/head schematic, mold and shot data, interface test requirements, mixed-model plan and shifts.

Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Confirm the feed/return schematic, head model, active mixing sequence, robot and turntable. Single-shot versus sequential zone filling and mixed-model operation require representative material and mold trials.

Ruta de producción

Dual-Density Car Seat Foaming Line Workflow

Define zones and materials → Confirm circuits and head → Dispense and mold → Inspect interface and output. Define preparation, filling, cure and output timing separately for the selected configuration.

01

Define zones and materials

Specify density and hardness separately and identify compatible recipes.

02

Confirm circuits and head

Map tanks, metering units, passages and active chamber routing.

03

Dispensar y moldear

Validate zone sequence, transitions and the cure process.

Especificaciones técnicas clave

Parámetros técnicos

Configuración existente y referencias de ensayo. Los ajustes del equipo, los resultados del material y los resultados del conjunto terminado son independientes; aplique cada valor solo a su configuración y condiciones documentadas.

Composición de la línea

Unidad de equipoCant.Función
3-Component Dual-Density High-Pressure Foaming Machine1 unidad2 POLY + 1 ISO, four-component dual-chamber L-type mixing head, closed-loop metering
Robot de vertido1 unidadVertido automático siguiendo trayectorias definidas, distribución uniforme y posicionamiento preciso
Turntable Line1 unidadMulti-station turntable, cyclic operation: pouring–foaming–mold opening–part removal
Sistema de control eléctrico1 unidadControl inteligente por PLC con ajuste de parámetros, supervisión de estado y alarma de fallos

Dual-Density High-Pressure Foaming Machine

ParámetroValor
ModeloHF-HPM-2A1B-DualDensityCarSeat
Component configuration3 components: 2 polyether polyol tanks + 1 isocyanate tank
Cabezal de mezclaFour-component L-type high-pressure mixing head with dual mixing chambers
Metering method3 metering units; flow meters + VFDs control output flow and mix ratio
Density adjustmentChange recipe or mixing index for two dual-density process routes
Caudal de vertido50–1000 g/s
Precisión de dosificación≤ ±0,3 %, en todo el rango dinámico
Configuración de tanquesIndependent temp control + circulation stirring for each tank
Control de temperatura20–45 ℃
Presión de mezcla10–18 MPa
Sistema de limpiezaPurga de aire automática, sin disolventes
Potencia5,5–7,5 kW
Sistema de controlPLC + pantalla táctil + almacenamiento de múltiples fórmulas
Sistema de aplicaciónDual-density cold-cure / high-resilience flexible foam system
Garantía1 año
CertificaciónCE, ISO9001

Dual-Density Foaming Process

ElementoDescripción
Component configuration2 polyether polyol tanks + 1 isocyanate tank
Mixing methodFour-component dual-chamber L-type mixing head, chambers adjusted independently
Metering control3 metering units with flow meters and VFDs
Density adjustmentChange recipe or mixing index to change foam density
Process routes2 density routes, switchable between soft layer and support layer
Mixed-line productionFront seat, rear seat and headrest on one line
Existing application note: Specifications are illustrative and customizable per project; contact our engineers for project-specific configuration. Original process references, with their existing values: Density fluctuation ≤±3%; Dosing accuracy ≤±0.3%; Cycle about 60 s; Pouring rate 50–1000 g/s; Up to 1,100 pcs per line per day; Changeover ≤20 min, CE & ISO9001. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.
Productos relacionados

Equipamiento auxiliar para su línea de espumado

Las referencias de equipos se seleccionan según su proceso documentado. La dosificación principal, el suministro auxiliar y las rutas alternativas no constituyen un único paquete estándar.

Ventajas de la solución

Controles de proceso y verificaciones de aplicación

Evalúe estas funciones con el material, los moldes y el resumen de producción seleccionados. Los resultados de las piezas acabadas requieren su propia evidencia de aceptación.

Clear feed architecture

Separate primary components, metering circuits and head chambers in the configuration description.

Validated zone transition

Establish interface quality with the selected materials and mold.

Defined production basis

Balance cycle, molds, model changes and work schedule rather than combining headline values.

Casos prácticos

Proyectos relacionados

Estas son referencias de aplicación relacionadas. Compare el material, el proceso y los módulos entregados reales; las cifras de proyecto reportadas no son resultados de aceptación para otra línea.

Ver todos los proyectos

Preguntas frecuentes sobre la planificación de la producción

Selección, alcance de suministro y validación para esta ruta de producción.

How do the three-component and four-component head descriptions relate? +
The current technical references use both descriptions. Confirm the original head drawing and feed/return schematic before interpreting the circuit count; no replacement count is assumed here.
Does changing index guarantee a second density? +
No. Any recipe or index change must remain within material-supplier limits and be validated for density, hardness, cure and zone bonding.
¿Qué información se necesita para una configuración preliminar? +
Seat zone map, recipes, feed/head schematic, mold and shot data, interface test requirements, mixed-model plan and shifts. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

Obtenga una cotización gratuita

Share the following with your production brief: Seat zone map, recipes, feed/head schematic, mold and shot data, interface test requirements, mixed-model plan and shifts. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

Contáctenos

Para saber cómo tratamos la información de su consulta, lea nuestra Política de privacidad.

Revisión de la configuración basada en la aplicación y los datos del material Documentación acordada de equipo, interfaces y aceptación Formación y soporte definidos para el paquete suministrado
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube