Máquina de fundición de nailon MC al vacío | Piezas de ingeniería
The HF-MCN150-VT package combines enclosed caprolactam preparation, vacuum dehydration, heated metering and mixing, and configured centrifugal or direct casting for MC Nylon components.
Caudal de descarga
5,0 a 45,0 kg/min (ajustable de forma continua)
Nominal Feed Split (Volume)
Nominal A:B = 1:1 by volume (supplied reference)
Referencia de precisión
±0.3% (Measured with steady thermal oil circulation)
Thermal-Oil Jacket Reference
135–140°C for tanks, pumps, valves and hoses
Deep Vacuum Anionic Polymerization for Heavy-Duty MC Nylon
La HF-MCN150-VT es una máquina industrial de colada al vacío de nailon fundido por monómero (nailon MC) diseñada para la desgasificación de caprolactama de alta pureza, la dosificación estequiométrica en circuito cerrado y el moldeo centrífugo de poleas y forros de desgaste para servicio pesado.
The HF-MCN150-VT is described in the supplied brief as a monomer cast nylon preparation and casting system for in-mold anionic polymerization of caprolactam into cast PA6 components. Dual heated preparation vessels, metering pumps and a dynamic mixing head supply the selected mold.
Centrifugal stations are configured for suitable rotational parts such as sheaves and bushes. Plates, solid rods and other shapes require their own direct-casting tooling and heating arrangement. Molecular weight, residual monomer, void content and mechanical performance depend on the material, geometry and validated process conditions.

Flujo de material y principio de funcionamiento
Solid Charging & Deep Vacuum Dehydration
Solid caprolactam is melted and vacuum-conditioned in the specified jacketed vessels. Vacuum setpoints and the reported sub-20 ppm moisture target are verified against the chosen formulation, sampling method and original test records.
Additive Dosing & Stoichiometric Conditioning
The liquid monomer is divided into Tank A (monomer + catalyst, e.g., sodium hydroxide) and Tank B (monomer + activator/color/lubricants), maintained under positive nitrogen pressure (0.05 MPa) to prevent oxidation.
High-Speed Laminar Mixing & Discharge
Heated pumps meter the prepared A and B streams into the dynamic mixing head. The supplied brief specifies a nominal 1:1 volumetric split; the mass ratio and catalyst/activator recipe are calibrated separately.
Centrifugal Filling & In-Mold Anionic Polymerization
The mixed monomer is delivered into preheated tooling for in-mold polymerization and crystallization. Centrifugal molds use an approved speed for their geometry and load; direct-casting molds use their own filling sequence. Cure time is confirmed for the formulation and section thickness.
Controlled Annealing & Demolding
Solidified components are demolded and transferred to continuous step-down oil baths or thermal ovens for crystalline stress-relieving annealing to ensure dimensional stability and prevent warpage.
¿Necesita una cotización de este equipo?
Solicitar presupuestoModelo y parámetros técnicos
Supplied HF-MCN150-VT configuration data. Vacuum performance, post-degassing water content and centrifugal speed require original test records. Maximum component diameter and maximum rotational speed are separate limits, not a simultaneous operating guarantee. The permitted speed is established for the mold, mass, balancing, fixtures and load.
| Parámetro técnico | HF-MCN150-VT |
|---|---|
| Componentes | 2 Streams (Tank A: Monomer + Catalyst, Tank B: Monomer + Activator) |
| Rango de salida | 5,0 a 45,0 kg/min (ajustable de forma continua) |
| Rango de relación de mezcla | Nominal 1:1 A/B volumetric feed split in the supplied brief; mass basis and formulation calibration require confirmation |
| Referencia de precisión | ±0.3% (Measured with steady thermal oil circulation) |
| Alimentación eléctrica | 380 V, trifásica, 50 Hz (opcional personalizada 440 V/480 V, 60 Hz) |
| Presión de trabajo | 0,3 a 0,6 MPa (líneas de dosificación y cabezal de mezcla dinámica) |
| Capacidad de tanque/tolva | Day tanks: 2 x 150 L (Stainless steel with vacuum/oil jacket) |
| Peso | 3,800 kg (Main melting skid and centrifugal station) |
| Dimensiones (L×An×Al) | 3400 mm x 2400 mm x 2650 mm |
| Grado de vacío de desgasificación | ≤ 0.01 kPa (Absolute pressure); Thin-film falling chamber |
| Maximum Heating Temp | 150°C (Circulating thermal oil jacket); Melting vessels and feed lines |
| Centrifugal Table Speed | Supplied drive range 400–1,200 RPM; permitted operating speed confirmed for the specific mold, load and balancing records |
| Monomer Moisture Content | Reported target <20 ppm after degassing; Karl Fischer method and original sampling records require verification |
Características clave del equipo
The package covers enclosed caprolactam melting and vacuum preparation, heated metering, dynamic mixing, the specified centrifugal casting stations and controls. Annealing oil baths and horizontal plate fixtures are optional. Caprolactam and chemical additives are supplied separately; the central thermal-oil source and dry nitrogen supply are customer interfaces. Direct casting of plates, rods and tubes uses shape-specific tooling and process configuration.
Vacuum Monomer Preparation
The specified falling-film vacuum stage conditions the monomer before metering; final water content requires a defined measurement.
Configured Centrifugal Casting
Rotational tooling is selected for the part geometry, permitted load and approved speed envelope.
Heated Material Path
Thermal-oil jackets condition tanks, pumps and feed lines; mold heating has its own temperature settings.
Dry Nitrogen Interfaces
The specified enclosed vessels and transfer interfaces use the agreed dry nitrogen supply and process controls.
Hablemos de la configuración de su equipo
Comparta su producto, materiales, utillaje y requisitos de producción para que podamos revisar el equipo y las interfaces para su proyecto.
Preguntas frecuentes
Why is vacuum dehydration below 0.01 kPa essential for MC Nylon?
What is the advantage of centrifugal casting for large sheaves?
How does the machine prevent molten caprolactam from freezing in lines?
Can solid lubricants like molybdenum disulfide (MoS₂) be added?
¿Listo para hablar de su proyecto?
Contacte con nuestro equipo