خلفية لافتة حل صب ألواح النايلون MC السميكة

حل سباكة ألواح النايلون MC السميكة

اضبط صب ألواح النايلون MC السميكة مع التعبئة بمساعدة الإمالة والتجهيزات القالبية الحرارية والفحص الداخلي المحدد.

تكوين العملية

تبلور اتجاهي منخفض الفراغات لألواح بلاستيكية ذات مقاطع سميكة

تتطلب ألواح النايلون المصبوبة السميكة مونومرًا مكيّفًا وتعبئة مُتحكَّمًا بها وبلمرة ومعالجة حرارية لاحقة. والإمالة والتسخين المناطقي هما ضوابط عملية، وليسا دليلًا على وجود مركز صلب خالٍ من الانكماش. ويجب أن تحدد هندسة اللوح والمادة وخطة الفحص جودة المركز الداخلي والأبعاد المسموح بها.

نطاق توريد محدد

اتفق على وحدة الصب وفراش الإمالة والقالب والمناطق الحرارية وواجهات التلدين/التشطيب. تختلف إعدادات المعدات عن صلادة اللوح والسماكة النهائية واستقرار التشغيل الآلي.

المدخلات لاختيار العملية

أبعاد/سماكة اللوح، والتركيبة، وسماكة سماح التشغيل الآلي، والعيوب الداخلية المسموح بها، وخريطة الصلادة، ومتطلبات المعالجة الحرارية.

يُتفق على نطاق المعدات وواجهات المصنع المحتفظ بها والقبول بالنسبة للمادة والجزء المختارين. اتفق على وحدة الصب وفراش الإمالة والقالب والمناطق الحرارية وواجهات التلدين/التشطيب. تختلف إعدادات المعدات عن صلادة اللوح والسماكة النهائية واستقرار التشغيل الآلي.

مسار الإنتاج

سير عمل صب ألواح النايلون MC السميكة

تحضير المونومر والقالب ← الإمالة والتعبئة ← البلمرة والتبريد ← التلدين والفحص. حدّد توقيتات التحضير والتعبئة والمعالجة والخرج كلًا على حدة وفق التكوين المختار.

01

تحضير المونومر والقالب

تأكد من التكييف والتحكم في الرطوبة وترتيب تجهيزات اللوح.

02

الإمالة والتعبئة

تحقق من الميل المختار وتسلسل إمداد المادة.

03

البلمرة والتبريد

Develop the thermal sequence for thickness, shrinkage and material behavior.

تكوين العملية

النطاق الهندسي للحل المرجعي

مراجع التكوين الحالي والاختبار. تُعد إعدادات المعدات ونتائج المواد ونتائج التجميع النهائي منفصلة؛ ويُطبَّق كل قيمة فقط على التكوين والظروف الموثقة الخاصة بها.

المعاملالقيمة / الوحدةالتكوين / الظروف المطبَّقة
Maximum Sheet Dimensions2,000 mm length x 1,000 mm widthLarge-format horizontal plate casting bed
Plate Thickness Envelope20 to 200 mm (Stepped frame adjustment)Heavy welded steel mold frames with hydraulic clamping
إنتاج سحب المونومر المستمر5.0 to 35.0 kg/minوحدة مضخة عالية الحرارة متغيرة السرعة مستمرة ومدارة بمحرك سيرفو
Cured Rockwell Hardness ProfileR116 to R120 (Target R118)ASTM D785 testing on fully crystallized PA6 matrix
Horizontal Table Tilting Angle3.0° to 15.0° (Hydraulic stepless tilt)Motorized tilt mechanism with angle encoder
Plate Thickness UniformityWithin ±0.3 mm across entire slabPrecision ground heated platens with multi-point locking
Existing application note: MC Nylon uses caprolactam anionic polymerization. Mass and volume ratios are set using the relevant density and temperature. Finished hardness and flatness depend on annealing and machining; ±0.22 mm is a reference after face milling. Original process references, with their existing values: Tank vacuum ≤ 0.01 kPa; Moisture < 20 ppm; confirm for selected material and tooling; Incline angle 3°–15°; N2 purge pressure 0.05 MPa; confirm for selected material and tooling; Flow rate 5.0–35.0 kg/min; Ratio accuracy ±0.3%; confirm for selected material and tooling; Bottom temp 165°C; Top temp 155°C; In-mold dwell 25 min; confirm for selected material and tooling; Anneal temp 150°C; Thickness tolerance ±0.3 mm; confirm for selected material and tooling. Supplementary references: monomer 135°C, tool tilt 8°, delivery 25 kg/min, slab mass 350 kg and oil control ±0.5°C. The existing 99.2% conversion and 100% solid-core statements require original material analysis and internal inspection; neither is assumed from the thermal equipment alone. Confirm the configuration, material, test method and cycle endpoints before using reference values as acceptance commitments.

المعدات الأساسية لهذا الحل

تُختار مراجع المعدات وفق عمليتها الموثّقة. القياس الرئيسي للجرعات والإمداد المساعد والمسارات البديلة ليست حزمة قياسية واحدة.

ضوابط العملية وفحوص التطبيق

قيّم هذه الوظائف باستخدام المادة والتجهيزات القالبية الموجزة الإنتاجية المختارة. تتطلب نتائج الأجزاء النهائية أدلة قبول خاصة بها.

Controlled filling

Use tilt and delivery settings established with the actual plate mold.

Thickness-specific thermal review

Evaluate core behavior and shrinkage for the intended section rather than assuming a defect-free center.

Defined plate acceptance

Specify internal inspection, thickness measurements and hardness sampling.

مشاريع ذات صلة

هذه مراجع تطبيقية ذات صلة. قارن المادة الفعلية والعملية والوحدات المسلّمة؛ فأرقام المشاريع المبلَّغ عنها ليست نتائج قبول لخط آخر.

مراجعة المشروع
أسئلة التخطيط

الأسئلة الشائعة

Does directional crystallization guarantee a solid plate core? +
No. Validate the thermal process and inspect representative plates using an agreed method, coverage and defect criterion.
How is hardness uniformity established? +
Define specimen conditioning, test method and measurement locations across the actual plate and thickness.
ما المعلومات المطلوبة لإعداد تكوين أولي؟ +
Plate dimensions/thickness, formulation, machining allowance, permitted internal defects, hardness map and thermal-treatment requirements. Identify the equipment and interfaces to retain, plus the required test and acceptance documents.

ناقش أهدافك الإنتاجية

Share the following with your production brief: Plate dimensions/thickness, formulation, machining allowance, permitted internal defects, hardness map and thermal-treatment requirements. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.

اتصل بنا

لمعرفة كيفية تعاملنا مع معلومات استفسارك، اقرأ سياسة الخصوصية.

مراجعة التكوين بناءً على بيانات التطبيق والمواد وثائق المعدات والواجهات والقبول المتفق عليها تدريب ودعم محدَّدان للحزمة المورَّدة
Haifeng Polyurethane Machinery on TikTok
Haifeng Polyurethane Machinery on Instagram
Haifeng Polyurethane Machinery on Facebook
Haifeng Polyurethane Machinery on X
Haifeng Polyurethane Machinery on LinkedIn
Contact Haifeng Polyurethane Machinery on WhatsApp
Haifeng Polyurethane Machinery on YouTube