
حل الإطار الشمسي البحري البحرية
Develop closed-box PU injection pultrusion for marine PV frame profiles with defined material and module tests.
Heavy Structural Composite Framing for Offshore Floating Solar
Marine framing requires a specified profile, reinforcement, resin, connections and exposure assessment. Sealed resin conditioning and controlled injection support processing but do not independently establish corrosion life or electrical suitability. Metering pumps deliver the liquid resin components; they do not convey the continuous reinforcement.
نطاق توريد محدد
Agree the conditioning, mixing and injection-box scope with the die, puller, dry-gas and cutting interfaces. Alternative glass, basalt or carbon reinforcement requires its own process and component review.
المدخلات لاختيار العملية
Profile and connection drawings, fiber form/content basis, resin data, marine exposure, electrical requirements and line interfaces.
Equipment scope, retained factory interfaces and acceptance are agreed for the selected material and part. Agree the conditioning, mixing and injection-box scope with the die, puller, dry-gas and cutting interfaces. Alternative glass, basalt or carbon reinforcement requires its own process and component review.
Offshore Marine Solar Frame Workflow
Define profile and exposure → Prepare sealed resin supply → Inject and pultrude → Qualify profile and module. Define preparation, filling, cure and output timing separately for the selected configuration.
Define profile and exposure
Review frame section, connections, reinforcement and marine duty.
Prepare sealed resin supply
Establish conditioning, dry-gas and container-change procedures.
Inject and pultrude
Validate wet-out, die control and pulling for the selected fiber content.
النطاق الهندسي للحل المرجعي
مراجع التكوين الحالي والاختبار. تُعد إعدادات المعدات ونتائج المواد ونتائج التجميع النهائي منفصلة؛ ويُطبَّق كل قيمة فقط على التكوين والظروف الموثقة الخاصة بها.
| المعامل | القيمة / الوحدة | التكوين / الظروف المطبَّقة |
|---|---|---|
| Dosing Output Capacity | 1.0 to 10.0 kg/min | Hastelloy-coated servo-driven axial piston metering skid; supplied reference requiring configuration or test verification |
| ضغط عمل المائع | 12.0 to 15.0 MPa | Continuous high-pressure closed-die impingement injection; supplied reference requiring configuration or test verification |
| Supported Fiber Volume | Up to 83% (Vf) | E-CR glass, basalt, or carbon fiber dense structural packing; supplied reference requiring configuration or test verification |
| Salt Spray Durability Limit | Greater than 9,000 hours | ASTM B117 testing with flexural retention > 92%; supplied reference requiring configuration or test verification |
| Profile Wall Thickness | Up to 4.5 mm (Heavy section) | Engineered for 4-meter wave slap and typhoon wind loads; supplied reference requiring configuration or test verification |
| Continuous Pulling Speed | 0.8 to 1.2 m/min | Synchronized heavy hydraulic caterpillar puller; supplied reference requiring configuration or test verification |
المعدات الأساسية لهذا الحل
تُختار مراجع المعدات وفق عمليتها الموثّقة. القياس الرئيسي للجرعات والإمداد المساعد والمسارات البديلة ليست حزمة قياسية واحدة.
ضوابط العملية وفحوص التطبيق
قيّم هذه الوظائف باستخدام المادة والتجهيزات القالبية الموجزة الإنتاجية المختارة. تتطلب نتائج الأجزاء النهائية أدلة قبول خاصة بها.
Defined reinforcement handling
Keep fiber guidance separate from the resin pump and mixing circuits.
Wet-out evidence
Verify the actual reinforcement fraction and impregnation rather than inferring quality from pressure.
Marine-system validation
Assess resin, fiber, connections and module performance under the intended exposure.
مشاريع ذات صلة
هذه مراجع تطبيقية ذات صلة. قارن المادة الفعلية والعملية والوحدات المسلّمة؛ فأرقام المشاريع المبلَّغ عنها ليست نتائج قبول لخط آخر.
الأسئلة الشائعة
أسئلة فنية لتحديد نطاق المعدات ونافذة المواد وخطة التحقق.
Does a salt-spray duration establish offshore service life?
Can every listed fiber use the same settings?
ما المعلومات المطلوبة لإعداد تكوين أولي؟
Request an Offshore Marine Solar Frame Proposal
Share the following with your production brief: Profile and connection drawings, fiber form/content basis, resin data, marine exposure, electrical requirements and line interfaces. Our team will reply within one business day. Once requirements are clear, we provide a preliminary proposal within two business days.
